Jump to content
SAU Community

Gtst Spares

Weapon
 Share

Recommended Posts

Weapon Mentor

Weapon

Posted
Posted

Ok guys and girls

I have a R33 series 1 shell that is getting stripped (no engine,gearbox,diff)

All glass (rear window, front window, side glass and 3/4 glass)

all are in good condition and can be freighted at buyers expense

Front $150

Rear $250

Side $100ea

3/4 $200ea

Nismo Smoked indicators (as new condition)

$50

Standard Front guards good condition

$150pair (may separate)

Series 1 Bonnet good condition

$200

Msports Side skirts $220 as new

Msports Rear Bar $250

Trust Front Bar (needs a little fiberglass work) $100

Full wiring loom for R32 Rb26 into 33 GTST

Save thousands getting it done when you can buy mine :) for $350

(Engine loom is spliced into GTST dash loom for stress free intergration)

Engine Mounts to suit RB26 into R33 GTST

$100pair

Standard R32 GTR turbos good condition approx 82xxxkm's (inc std dumps)

$320pair

i also have starter motor, alternator, a/c pump, power steering pump, etc

Standard RB26 block with standard crank rods and pistons

(cylinder no6 fried piston ring however perfect for a rebuid, block is slightly scored and can be rectified with just a hone)

$400

Alpine MRP M500 mono amp 2months old $320delivered

Alpine Type R Sub in genuine alpine box $300

JVC

Bought approx 3months ago

RRP $769

Looking For $550ono (comes with all av cables software and JVC Carry Case)

Elegant and slim HDD/microSD Hybrid camcorder with KONICA MINOLTA LENS, 35x optical zoom, easy to navigate Laser Touch Operation and 30GB HDD for up to 37.5 hours of recording, Two colours available: Silver and Red

1/6-inch 800k pixel CCD

30GB Internal Hard Disk Drive for up to 37 hr. 30 min. of recording

7 hr. 10 min. of the best quality recording (ULTRA FINE)

35x Optical Zoom / 800x Digital Zoom

Memory Card Slot for microSD

Software provided (for Windows ®)

KONICA MINOLTA LENS

Gigabrid Engine

Laser Touch Operation

2.7" 16:9 Widescreen Clear LCD Monitor

Auto LCD Backlight Control

Auto Illumi. Light

Data Battery

Picture Titles

Quick Restart

Direct DVD Button/Direct Backup Button

USB2.0 High-Speed Transfer

Find out lots more for GZ-MG330R

Attached thumbnail(s) blank.gif Reduced 71%post-784-1232076541_thumb.jpg 550 x 440 (144.13K)

Feel Free to contact me via PM or 0404585529

I am located in Townsville 4814 for shipping reference

Cheers Marty//

Link to comment
https://www.sau.com.au/forums/topic/253529-gtst-spares/
Share on other sites
Weapon Mentor

Weapon

Posted
  • Author
Posted

Also forgot to mention that i have a full set of R33 Series 2 dampers and struts out of 97model with 72xxxkm's on them $350

Front only R33 sereis 1 dampers and struts 78xxxkm's $100pair

Both are in great working order and no leaks

Cheers marty

Link to comment
https://www.sau.com.au/forums/topic/253529-gtst-spares/#findComment-4381480
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you done the Ignition Sync Wizard in the AEM software?
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • MBS206
      RB25DE NEO with Haltech ECU

      By MBS206 · Posted

      You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • sonicii
      Could it really happen......

      By sonicii · Posted

      I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...