Jump to content
SAU Community

Deca Accommodation - Fri 27 / Sat 28 February


Recommended Posts

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

Accommodation sorted, thanks Bec :huh:

PS: If anyone (that knows me) wants a lift up there (on Friday) and a lift back (on Saturday), i have room in my car. Live in the western suburbs, so only people round the west/north; unless you want to leave your car at my place.

Hey, Just wandering when you need to know about beds, cos ill prob be interested in 4. But wont know for a day or 2. If thats too much of a hassle i can sort out my own. Thanks

Yeah no worries - Ill probably need to confirm rooms with the hotel on Monday - so a day or 2 is fine Vince.

The rest of you - speak up if you want something booked for you.

Julliette - confirm ill book you a room for both nights. If I can find another girl, will sort that out, otherwise will get you something to yourself.

Ill probably need to confirm rooms with the hotel on Monday

The rest of you - speak up if you want something booked for you.

Julliette - confirm ill book you a room for both nights. If I can find another girl, will sort that out, otherwise will get you something to yourself.

Bec

Could you book a room for Leon (achoo)& Shane for the Fri/Sat nights.

And with Al going home on Saturday i will have room for Julliette on Sat night if ya need .

Bec

Could you book a room for Leon (achoo)& Shane for the Fri/Sat nights.

And with Al going home on Saturday i will have room for Julliette on Sat night if ya need .

Will do Wayne

& Julliette - your staying both nights yeah?? I thought you were, but just confirming.

Anyone else - still have a couple of rooms left

Am confirming early this week, so if I dont have you down. You'll be on your own to book rooms.

Send me a PM or let me know if your keen.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...