Jump to content
SAU Community

Recommended Posts

hi,

i am selling my freshly built 26......

consisits of

micro polished and grub screwed crank

block dipped and crack tested, chemicsally cleaned

new welsh plugs

arp main studs

pauter rods

cp pistons with custom gudgeon pins .20 thou oversize

all balanced and blueprinted

jun oil pump

ati super damper 1000hp balancer

very veyr big and polished port job...

cc chambers

arp head studs

edges deburred

metah headgasket

ferrera oversized valves

hks 272 10.2mm lift camshafts in and out

hks step 2 valve springs

jun type b titanium retainers

bronze valve guides

high energy sump to suit rwd

adjustable cam gears

owes me 16,8000

after 13000 firm....

its brand new, sitting on engine stand

also have a hypertune plenum for sale to suit rb26 single throttle, was slightly damaged but has been repaired......

after $2000

alsh have a jim berry full race clutch for sale....

$1000 no offers

60mm sub zero wastegate from usa... worth 1400 sell for

$500 no offers

and a 1000hp sx fuel pump...... worth 1100

sell for $ 600

please pm me or call for genuine people, i dont want to sell this but am forced to.......

was all going into my s15...

ph

denis 0404 490 095

ill have more pics this arvo of everything....

post-23519-1232662378_thumb.jpg

Edited by den001
Link to comment
https://www.sau.com.au/forums/topic/253781-full-house-rb26-engine-for-sale/
Share on other sites

  • 2 months later...

also. price drop on the hypertune plenum, 1500 no offers....

engine is also abit cheaper, as i am keeping the jun oil pump and ati balancer......

10 grand for engine.... no offers

new pics....

post-23519-1238667968_thumb.jpg

post-23519-1238667999_thumb.jpg

post-23519-1238668022_thumb.jpg

post-23519-1238668061_thumb.jpg

post-23519-1238668094_thumb.jpg

post-23519-1238668144_thumb.jpg

post-23519-1238668188_thumb.jpg

post-23519-1238668238_thumb.jpg

post-23519-1238668281_thumb.jpg

post-23519-1238668316_thumb.jpg

Edited by den001

This is a dead set bargain.

I couldn't build this myself for that price if i worked for free.

Good luck with the sale Dennis...im sure it wont take long to move it on.

bump com on guys, som1 must need quality parts

Hi, I am in the process of building a Strong RB 26 for one of my GTR33 track car. will talk to mechanic and engine builder regarding your gun engine. my mobile is 0433559972 Melb. Alex

BTW I am rebuilding another RB26, I am chasing a set of forged pistons +20 and a good GTR33 crank to finish this one. 455AWKW with T88

silver GTRHKS

cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...