Jump to content
SAU Community

Recommended Posts

I just got an Autometer boost gauge, the white one and was wondering if anyone knows where it can be mounted, rather than the pillar. Just want to put it somewhere where i can see it whilst driving, but thieves can't when looking into my car?

Also, they are pretty easy to install right? Anyone done their own before?

Cheers

Kris

Link to comment
https://www.sau.com.au/forums/topic/25448-autometer-boost-gauge/
Share on other sites

dont bother with the din slot - you'll never be able to see the needle over the lip of the gauge.

been there.

be like me - tough and dangerous - and zip tie the baarstard to the vent - it's cheap and it's functional...and you get extra street cred for being tough and povvo like me.

Originally posted by zanda

dont bother with the din slot - you'll never be able to see the needle over the lip of the gauge.

been there.

be like me - tough and dangerous - and zip tie the baarstard to the vent - it's cheap and it's functional...and you get extra street cred for being tough and povvo like me.

Zanda,

If that is the case, you car must have lots of street cred hehehe isnt held together by zip ties.

Sits back waiting to be spanked :shake:

hahaha sounds familiar and just as dodgy Paul!!! :)

double sided tape probably wont work, because it doesnt stick to the dash and stuff very well (unless its on a flat bit).

Just go a DECENT pillar mount and do it properly the first time. It looks the best IMHO and is the most conveniant method

Trust me...... i know these things (isn't that rite paul :mad: )

yeh it will work out the easiest

I have a cheap imitation style pillar mount, which does the job. it looks kinda shithouse though. I bought it from Motoquipe (not a bad little semi-rice shop in floreat) for like $20

Places like supercheap etc sell universal pillar mounts, but for a proper moulded one for a 33, your looking at $$$.

The skyline i almost bought had a boost guage mounted just behind the steering wheel too. That looked pretty good too. I've got some pics if you want them (email i guess).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
×
×
  • Create New...