Jump to content
SAU Community

Recommended Posts

My dog has been in the house since yesterday and wont get out - tried to get him out last night but he ran off and has been under my bed ever since and growls and tries to bite me if I stick my hand under there lol

  • Replies 193
  • Created
  • Last Reply

Top Posters In This Topic

lol ^ my german shepard has been lying on the cool tiles right under the air con vent for the last 3 days . only time he moved was last night i turned the hose on out the back and he came running to play under the water :-)

I got brutas one of those half shell/clam kiddy pools. Shame he doesnt like water.

We got our Staffy a little wadding pool yesterday so she could cool off. Not fair we swim int he pool and she doesn't have her own :)

I definately agree with you there Matt. Dry heat is easy to climatise, nothing worse than sweating 24/7.

More importantly the poor folks (like me) who dont have reverse cycle (evaporative only) don't suffer too much. In humid weather our ducted evap system is next to useless

-D

Its a miracle I invented a light speed rocket house,,, so i thought????, my house can fly..... cool, I woke up and stepped out on the face of the SUN...LOL

holy cats the sun is hot today.lol like stepping into a sauna while being burned with molten metal.

I love the heat but its going to be a long week of it..lol

when i took the hose from the rain water tank to the birdbath.... the birds just about fell out of the trees at my feet in a que to get in the water..lol somehow i have about 300 birds in my yard now , hiding from the heat , ended up filling up a few buckets for them to drink from.

MOOMBA, no way,quality of life is worth more then money , not die from heat all the time. give me a beach anyday over a dust bowl with the worse flies on the planet.

Edited by sapphiregraphics

and welcome to another edition of f**k i wish i was dead this afternoon!

hmmm... someone wanna put my coilovers n shiz in? i keep putting it off till late at night but never get around to it ahaha.

lol ^ my german shepard has been lying on the cool tiles right under the air con vent for the last 3 days . only time he moved was last night i turned the hose on out the back and he came running to play under the water :-)

lol same thing here, i got a Shepard myself and we dont usually let him in the house but last few days he been sleeping next to me haha. And he normally runs like crazy when i pick up the water hose...now he just kept following me wanting to get soaked :down:

More importantly the poor folks (like me) who dont have reverse cycle (evaporative only) don't suffer too much. In humid weather our ducted evap system is next to useless

-D

Yep, Evaporative A/C systems are pretty much useless in humid climates - NSW, QLD, NT, Northern WA etc.

i went to get a defect cleared yesterday so i could drive my car till the regency appointment date. the cop didnt even come outside to look at my car. just signed the paper and said be stuffed if im going out there if u have to go to regency anyway.

Last night began to cool down a bit once that breeze came through...i swear i was cold last night from the wind coming through the window. Apparently at 8am, the time I'm writing this, its 27 at marion, hopefully it stays cooler today.

Yesterday we suffered the scheduled power black outs. My work was out for a while and so was Marion shopping centre, was on the way home during this though so missing out on the chaos.

I'm hoping it cools down a bit tonight so I can wash my car.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...