Jump to content
SAU Community

More Shit For Your R34 Gtr - Bride Stradia Sport Seats, Cusco D1 Cage, Front Diffuser, Hks Fuel Rail, Sard Fpr, 5zigen Exhaust, Nismo Clutch,


Recommended Posts

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

are the cluster and cage for an r33?

Cluster wont fit your R33, but the cage might. I'll try and find out.

hey eugene

I'm interested in the tires will they be good for my 19 x 11 that I bought of you?

and are they semi slicks or just normal tires?

regards Jordan

Nismo clutch SOLD.

GT-C rims SOLD.

Update on the parts left over.

- Genuine Bride Stradia Sport seats, BRAND NEW, pair, including Bride seats rails to fit R34 GTR --- $3500

- Cusco D1 5 point half cage, BRAND NEW, full chrome moly --- $1200

- HKS fuel rail, used --- $280

- Sard fuel pressure regulator, normal model, used --- $150

- 5Zigen Fireball cat-back exhaust, full 3" stainless, no mid muffler, loud without silencer but quiet with it on, used ---$600

- Genuine Nissan front plastic diffuser, I have both new and used one --- $1150 new, $700 used

- Nismo G-Max twin plate clutch kit, used but only travelled about 10,000kms - $1000

- GReddy eManage harness kit, NEW --- $180

- VOLK GT-C in 19 x 10.5 +11, PAIR ONLY, Brand New, Face 2 with curved spokes, Silver colour --- $2500

- AVS Model 5 wheels with tyres, 18 x 10 +18 all round, silver spokes, no gutter marks, set of 4, used - $2000

- Volk GT30 in 19 x 10.5 +17 - Formula Silver, rims only, set of 4, NEW - $4200

- Kumho KU31 275/30R19 x 4 tyres for above rims, NEW - $1100

- Trust/Greddy Spec R HG, Type23 Intercooler, 115mm thickness, Brand NEW - $2400

- Trust/Greddy hard pipe kit for cooler, NEW - $750

- Trust/Greddy aluminium radiator pipe, NEW - $150

- Nismo front bar in Bayside Blue, USED but in excellent condition - $1800

- HKS SSQV kit including aluminium pipe, NEW - $650

- Sard fuel rail, NEW - $350

- Standard Nissan GTR cluster, used, unknown kms --- $300

More pics of used diffuser as requested.

Sorry if a stupid question, but will the diffuser bolt up to a GTT?

hey eugene, could i get some pictures of the avs wheels please.

Np David i'll take some pics tonight mate

cheers

Hi Eugene,

Can I give you an offer for the Bride Seats?

Thanks

Sure Matt, I can only say yes or no, right? :)

Btw pics up for the AVS wheels.

post-2802-1236518203_thumb.jpg

post-2802-1236518234_thumb.jpg

post-2802-1236518246_thumb.jpg

post-2802-1236518257_thumb.jpg

post-2802-1236518268_thumb.jpg

what size tyres on the AVS wheels?

would you take swaps for 19" AVS wheels in 9"/10" (have to check offset ive forgotten)

what size tyres on the AVS wheels?

would you take swaps for 19" AVS wheels in 9"/10" (have to check offset ive forgotten)

Sry but i have no use for staggered rims. All my 3 cars are AWDs.

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
×
×
  • Create New...