Jump to content
SAU Community

Recommended Posts

  • Replies 79
  • Created
  • Last Reply

Top Posters In This Topic

I've got a black Series 2 R33 skyline up for wrecking... It's been hit in the right front qtr...so radiator, condensor, front bar, front right qtr panel, rad support are gone...but mostly everything else is up for grabs...

If your after anything just pm me cheers...

Engine Bay

Rb25det 116xxxkms with loom and ecu (remapped by dr drift) & Splitfire coil packs - $2400ono

post-36648-1233733820_thumb.jpg

S2 Rb25 turbo with actuator, good cond, minimal shaft play. Didn't blow any smoke - $250

S2 AFM (pink sticker)- $90

R33 aircon compressor pump - $100

R33 power steering pump - $100

R33 alternator - $80

Fuse box lid - $20

Stock airbox & snorkel + filter - $75

Exterior

Gold 18" x 8.5 (+15 offset) Gravity Gullframes with tyres (90% tread on 2 tyres), one wheel has gutter rash - $1200

Passenger Side Headlight - $150

Driver side Door - $180

Passenger Door - $180

Boot Lid - $200

Stock Rear Bar - $90

S2 Spoiler - $50

Nismo Side Indicators - $50

Interior

Instrument cluster, white face $150

Dash surround (with clock, hazard switch etc) - $80

Gear stick surround - $40

Ashtray - $20

Glovebox - $40

Steering column surround plastics - $25

S2 dash pad (no passenger airbag & panel) - $40

Centre console - $50

R34 Front seats - $150 (to fit r33)

R34 Rear seats - $100 (fits both r33 and r34)

R33 S2 Front seats (drivers side has a tear in the usual spot) - $80

R33 S2 Rear seats, good condition - $40

Seatbelts, full set - $80 (will seperate)

Ignition barrel + door barrels + key - $100

other parts...

Cat Back 2.5" to 4" tip - $150

Dump pipe - $50

2.5" Front Pipe - $100

Hybrid Front Mount Intercooler - $200

Pm me for any other parts cheers...

post-36648-1233734526_thumb.jpg

post-36648-1233735497_thumb.jpg

intrested in turbo and actuator.

located in melb

hey mate...

i'm after a working diff if you'll sell??

PM with a price. i can come pick up (assuming from plates that you're in melb somewhere)

cheers

hey bud just a question i heard the R34 seats wont fit into the R32 or R33 skylines due to floorpan construction. competely different, did u get rails made cause im trying to find some for my R32

i know the R33 rail is the same as the R32 :down: lol id grab yours if i could lol

  • 2 weeks later...

Hey mate,

Tryed to PM but you box full. Lots of messegaes ehhh? Please let me know if you still have the greabox. I am after a gearbox S2.

Cheers,

Eugen

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...