Jump to content
SAU Community

Help :( R32 Hard Brake Pedal, Can't Find Out What It Causing It.


Recommended Posts

Heres the story:

Bought an unreg R32 GTS4 that had been sitting for a while. And now it wants to go over the pits and has failed twice for a hard brake pedal. So far this has been done:

Brakes bled

Front & Rear calipers reconditioned

New pads fitted

Master cylinder reconditioned

Rotors skimmed

Brake booster pressure tested

The brakes react to first part of pedal travel but go solid when trying to press hard, ie in a emergency stop. This is why pits said they won't pass it.

NOTE: Car has factory ABS fitted.

So far, can't get rid of the hard pedal. Beginning to suspect while booster has passed pressure test, it is miss-performing. Has anybody got one that they can lend me to test? Or if it comes to it, anyone have a good condition one to sell?

Anybody had this problem before? (Rmb ABS fitted)

0431 985 155 is my dad's phone number (Tony).

(I'm still on Ls)

Sounds like air in the system,

But if you have bled them, it should of corrected the problem.

There is a particular way you bleed the brakes with ABS as well.

Not sure if that is just for GTR though.

Other than that, I am stumped!

Yeah, it's been done by my mechanic who used to do ferraris lambos tractors :thumbsup: (ex-barbagello) etc etc, basically fixes anything, except my line!

It doesn't feel like air cause if just driving normally, they are fine. Its when you brake to a certain point that it becomes rock solid and you really have to press hard for the car to stop. (Don't get me wrong, it stops really well, its just the hard pedal) The guy at the pits said sure, your average joe could stop the car, but he's referring to when say eg a girl is driving and they can't press the pedal, ie making it too dangerous.

I want the car on the road :| This is the only thing stopping it and its starting to annoy the hell out of me. Stupid skylines :P

Edited by Ten Four

Doesn sound like air in the system, that gives the opposite effect. You put your foot an the brake and nothing happens for a while because you're compressing the air.

Sadly, I cant think of what it might be.

Rhys,

Air in the system can in fact cause block peddle mate,

I understanded where you are coming from,

But to discount air from the system completely at this stage, may in fact lead you down the incorrect path.

There is a sequence that you have to bleed the brakes with ABS in a skyline if it is to be done properly.

There is write up for this in the GTR Manual that can be found online.

Once you have cleared the system completely, then can you move onto the next fault finding excercise.

Nav had a very similiar issue with his car.

Cheers

Mike

Thanks for the replies guys.

Flash, it's not much different, both on and off are pretty hard.

Mike, where is this guide? Otherwise the air has been pretty much discounted at this stage. Its acting more like the booster so I'm going to try get one (to a point its fine, after that its just hard). Cause the car still stops really well, its just the firm pedal.

Defective, the lines are not twisted or split cause each was tested. Brake fluid was replaced earlier today.

Ahh 33, I think I may just do that, thanks.

Edited by Ten Four

Have you tried taking it and stopping by a couple of performance workshops to get their opinion on what it could be? They might have come across this issue before and know the solution.

Yeah mate, as a last resort I will probably end up taking it to a performance workshop. I'm sure the problem is something silly. If the brake boosters I've just bought and the disabling the ABS don't fix it, I'll take it to one.

The brakes react to first part of pedal travel but go solid when trying to press hard, ie in a emergency stop. This is why pits said they won't pass it.

Who idea was it to do the above mentioned repairs ??

Get a Brake specialist to check it out . ( a good one also )

Rhys,

Air in the system can in fact cause block peddle mate,

I understanded where you are coming from,

But to discount air from the system completely at this stage, may in fact lead you down the incorrect path.

There is a sequence that you have to bleed the brakes with ABS in a skyline if it is to be done properly.

There is write up for this in the GTR Manual that can be found online.

Once you have cleared the system completely, then can you move onto the next fault finding excercise.

Nav had a very similiar issue with his car.

Cheers

Mike

Mmm i know you might be the guy who gave me the warn on this but ima have to say fail on that one aye, as a mechanic i can say that air in system will cause a spongey pedal and lesser response upon application

Its sounding more like booster but also check where the vacuum line connects to the manifold, start it with that line off and make sure its sucking in air, also check that the booster vacuum hose isnt sucking closed under vacuum when you push the pedal

Dsturbed, the car had been sitting for 1.5 years so the above jobs were done as to be expected. However, it didn't change the brakes much.

Takushi, that has been done a few days ago.

Update: it isn't the ABS.....

Edited by Ten Four

Hey might sound odd but can you post up a pic of the brake booster....

i had a brake specialist test my old TX-5 booster and it was fine then i had the same problem..

i found there was a one way valve in the booster due to boost and it was the wrong way around :D so please check you dont have one or it is the right way around.... also you say you tested the line,,, did you actually start the car with a vacume tester on it then rev to boost to see the difference?? and what was the difference??

Hi guys, problem seems to have been solved.

Previously, the master cylinder must have been taken apart as a washer was missing and the piston was bigger than usual (looked like nothing was out of place...). Replaced washer and put a shorter piston and it seems to have solved the problem. In essence, the car still brakes just as well as before, just with a softer pedal now.

Will be visiting the pits tomorrow.. Cheers.

Edited by Ten Four
Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...