Jump to content
SAU Community

Recommended Posts

Good Day all,

About 2-3 weeks ago my car starts to shake after i turn the ignition on. It will go away after a minute or so after i drive outside of the driveway. Occurs randomly. Thought it's something normal so i left it as it is.

Few days later when i start driving on the freeway the same thing will occur. The car will vibrate and shake for a few seconds. If it remains shaking / vibrating after a minute or so all i have to do is boost the car and the vibration will go away. This will occur when i'm driving about 70-80km/hr at the freeway. So what happens is i'll boost it to 100-120kph when the car vibrates at say 70kph and the vibration will just go away (not sure if this makes any sense)

So today arvo me and Brendan jack the car up to look for any exhaust leaks (checked out fine) and we also took apart the AFM and cleaned it with a electrical contact cleaner but it's still the same.

Also just drove to the city and along the freeway the vibration is getting worst. Was basically vibrating from my place all the way to the city. Tried boosting the car like i used to do but it seems to take longer to get rid of the vibration this time. Also noticed not gaining that much power when boosting the car as before and the exhaust is bloody loud now. Making a funny grumbling / misfiring sound.

Vehicle is basically stock. R34 GTT Series 2

Apexi pod filter.

Blitz Nur Spec Cat Back

Just changed my spark plugs last service from copper to NGK iridiums BKR6EIX gapped at 0.8mm

Any suggestions / help guys ?

exhaust from what i heard is a very slight mis firing problem...

the coil packs is what we planning to look at next after eliminating exhaust leak, afm, sparks. Im assuming its only just starting to go a little bit hence the randomess of the problem occuring.

Best recommended way of testing coilpacks would be? Replacing all of them spitfires? or maybe using someones elses coilpacks to see if it fixes the problem.. and if it does then buy the coilpacks?

Or is there a way to test using a multi meter?

it sounds like it may be your coils starting to go. you may need to look into that.

by vibrating is the car surging with a strange exhaust noise(ie popping/misfire)?

yeah the car will surge with the strange exhaust noise

it's like a spluttering noise (i.e. putting an empty bottle and submerging it into a pail of water - those kind of sd if you get what i mean)

It could be a vacuum / boost leak,

Check your intercooler and piping etc

if that was the case wouldnt the car have trouble holding boost?

His car holds the boost no problem...

Suppose it couldnt hurt to hunt around for the vaccum lines tho.

the coilpacks are a common problem, does it miss fire under load, say accelerating and does it start to do it around 5000rpm. if yes then l can safely say it is most likely coilpacks, if not try swaping in a known good set of coils and then try and if that fixs it buy some spitfires. Coils can be tested with a multimeter but it wont show up a intermitant fault like skyline coils have, because they have a problem with sealing and the spark jumps out the side of the coil in stead of tracking down the plug.

You can try taking the spark plug cover off then try driving the car at night and when it does it, look at your coils while the car is running and see if you can see any spark flashing around(sometimes you can see it in the dark). If yes get new coils.

hope that helps

gee you sure got lots of guessswork replies - you need to start methodically - first you check for engine fault codes - takes about 1 minute and you only need some wire to do this - if you don't know how, search the site (its been covered maybe a million times)

and why would someone tell you to replace the coils or even check them unless you get a definitely got a Code 21 ?????????? bizarre!

see what fault Code you get if any- you may not get one come up at all, but even that points you closer to the real problem and figuring out what needs doing

if no code comes up it maybe something as simple as water in the fuel, blocked fuel line or filter, or dying fuel pump, among about 15-20 possibilities

gee you sure got lots of guessswork replies - you need to start methodically - first you check for engine fault codes - takes about 1 minute and you only need some wire to do this - if you don't know how, search the site (its been covered maybe a million times)

and why would someone tell you to replace the coils or even check them unless you get a definitely got a Code 21 ?????????? bizarre!

see what fault Code you get if any- you may not get one come up at all, but even that points you closer to the real problem and figuring out what needs doing

if no code comes up it maybe something as simple as water in the fuel, blocked fuel line or filter, or dying fuel pump, among about 15-20 possibilities

I agree with this reply 100% and just to add to those 20 or so possibilities you could have leaking intake manifold gasket as I do and sometimes misses on idle.

Good luck!

Dave

Tried opening my kick panel to check on the ecu but it seems to be stuck. NFI so i'm trying the pin method via the fuse box under the driver's dash

Tried the pin method and ............... 5 short blinks and 5 fast blinks which means code 55 - no malfunction

Ok now what guys ?

p.s. This test was done without driving the car for 10 minutes to warm up the car. Will this give out a false reading (55) ?

Edited by hotchoc

yeah do the test codes thing but if it sorta sounds like a wrx when it starts shuddering its most likely the coils, could be simple like the coils clip isnt connected properly, thats what my problem was, i just opend the plastic cover concealing the coil packs on the engine and clipped them all in properly.

also this may fit the reason why when you boost it goes away, you boost it, all the parts of the car that arnt fastend to the car in some way will move and this could mean that the connection is made again, its also better to check this now instead of later because ultimately this will damge the coil if it is a connection problem. then your up for $400 ish for a set of new decent coils.

this worked for me but it could be many other issues aswell, coils could just be on the way out, even a sark plug that is fouled or dying ect.... but it sounds like something to do around that area anyway...

also i really doubt its the exhaust at all, i ran my car for a bit of fun while chageing the front/dump pipe with no exhaust from the turbo back.... awesome sound, no shuddering, just sounded like a drag car...

As I was saying before on msn, give the coils a proper servicing before you go out and buy splitfires.

- remove the coils

- remove the boot, clean, and then hit it lightly with silicon spray

- using a metal brush, clean the tip of the coil pack

- reconnect it.

but if your coils are on the way out, no amount of servicing will bring it back to life.

ecu won't always give you a fault code if it's coil related.. it might if it was a power transponder though.

oh one more thing, if the coil packs are not secured properly will the fault codes show as 55 as technically speaking there's nothing faulty with the coils but just a loose connection right ?

I didnt get any fault code, and my coil plugs were loose because the mechanic doidnt clip them in, the car ran fine for 2 day than i went over a speed hump and the problem started....

  • 4 weeks later...

just a small update ^

took the coil packs out and sprayed it with a contact cleaner and used a vacumn cleaner to suck out all the dirt and leaves (yes don't ask me how it got there) near the spark plugs

now the problem is gone - just hope it'll stay liek that for now

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I was using the wiring diagram I have So 12.74V is coming into the rear Fuel Pump relay as I measured.  When I turn the key to ON im getting 0.6V to the Fuel Pump plug; which i assume is backfeed voltage and doesnt include the 12V from ignition power.  The rear relay is working and being triggered.  From the diagram I clearly see the rear relay 80 = Rear Relay going into the Body/H loom (R-27) 27 = Fuel Pump plug going into the Body/H loom (T-20) 40 = Short Connector (R-27) I'm reading 12.74V on the blue/black wire which is the power for the Fuel Pump   From this diagram I can see the Ignition relay goes into the front and up to the ignition  2 = Fuel Pump Relay <1M> (R-27) 37 = ING Relay <1M> I started from the pump using this reference Which the way I read it (referencing Nissan wiring color codes) is: Pin Wire Color Function 1 B/P (Black/Pink) Ground 2 L/W (Blue/White)        ECU Trigger 3 SB (Sky Blue) Fuel Pump 5 L/B (Blue/Black) 12V Constant Tested SB to SB on Fuel Pump for continuity - confirmed Tested negative on Fuel Pump to 12V battery and L/B - confirmed 12V Pulled the relay putting 12V between Pin 1 & 2 and testing continuity on Pin 3 & 4 - confirmed relay   So that has me looking at this part of the circuit to understand whats happening here...and im still confused. From best I can tell; the disconnect is back to my previous diagram; between Ignition Relay and Fuel Pump Relay...which yet again; afaik is where the immobiliser should.    Thats what I was trying to explain to GTSboy; im not trying to fix it myself; yet I seem to have to get a Masters in Electrical Engineering (while im busy doing my actual job of DevOps & Cloud Engineering) somehow.  I just wanted more expert opinions; or more so that what I tested is correct and proves it to something around that area; to go back to the alarm tech (for a 3rd time) that he needs to fix it. He keeps telling me its not the alarm. He lives on the complete other side of the city so i understand not wanting to make a trip but as I said before if its the alarm it should be up to him to fix it. But he's adament its not; even though I pointed out the FP was immobilised through the original alarm. To my mind; it seems that the ECU is sending the signal; but the ignition is not getting 12V down the line.       
    • Maybe also really stiffly sprung track cars. Get the inside wheel up in a corner and all the fun stops. Also me sometimes (rarely) when I have to stand on the brake to convince the diff to drive the wheel that is still on the ground when I'm trying to diagonally get over severe driveway entrance, etc.
    • I feel like I'm missing something. You had an authorised installer come out and install a new alarm. Post install the car doesn't start, and you aren't getting the installer back to fix what they did wrong?
    • So either way it is gearbox out and look what is wrong?  I know about the input shaft bearing. Even before swap/new clutch the it sounded exactly like this: So is that inout shaft bearing or the other was installed backwards?  And can some please tell me the part number for that input shaft bearing? The gearbox is small box from R34 N/A and number is FS5W71C. Thank you  
    • I am yet to see anyone ever regret a quaife or helical. ...other than drifting/skidpan duties. I kind of want to upgrade my factory helical with a Quaife (but really it's not ultimately that different, and is a MASSIVE UNDERTAKING), that's how good the hype is about them, that I want to try them 'just to see'  
×
×
  • Create New...