Jump to content
SAU Community

Recommended Posts

Hi guys,

Im planning to take the hi flow turbo off my R32 gtst and put a standard RB25 unit on it as im after response the high flow is too laggy for me.

As far as I can tell everything will bolt up the same but the only difference im noticing you will see in the pic below where ive circled it in red.

On my standard R32 turbo on the left their seems so be some sort of fitting for a hose, but on the R33 turbo on the right it doesnt exist at all theirs not even a hole their like on the R32 one.

r32r33t.jpg

What does this thing do and do I need to modify anything on the R33 turbo to suit?

Thanks :P

Edited by Dave69001

on the R32 turbo that fitting is linked to the wastegate actuator. on the R33 turbo that fitting is on the bolt on elbow off the turbo, do you have the R33 elbow to go on the turbo?

if not, just run a vacuum line from the plenum to the wastegate actuator on the R33 turbo. when i did the same conversion on my 32 i drilled and tapped the compressor housing on the R33 turbo in the same spot as the R32 one. IIRC its 1/8" BSP-T.

me and my mates did the r33 turbo on my r32 the other week and we just ran the hose from the actuator and split it to the vacum hose from the 32 standard bov and the boost controller works fine

and i asked a performance mechanic if it is allright and they seen it and said it should be sweet

but could it cause some lagg the hoses being so long like cause the boost to take abit to register

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
    • Just like in being 14mm too small (296mm) makes it not fit, being 14mm too big (324mm) it also won't fit. You want to find the correct rotor.
    • @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
×
×
  • Create New...