Jump to content
SAU Community

R34 Mfd Replacement Screen

rtune
 Share

Recommended Posts

rtune Experienced

rtune

Posted
Posted (edited)

If you have a problem with your MFD LCD screen (busted scan lines, bad backlight, bad pixels),

then replace it with this fresh new one. I've done it. I can verify that replacing it with this panel

works great. Requires removal of MFD, and careful dis-assembly of MFD, connect two ribbon cables,

and re-assembly. Takes just 10 minutes and a screwdriver.

$200 plus $9.99 shipping bubble wrapped in anti-static foam.

post-51561-1234173000_thumb.jpg

post-51561-1234173013_thumb.jpg

Edited by moneypit
Link to comment
https://www.sau.com.au/forums/topic/256292-r34-mfd-replacement-screen/
Share on other sites
sun33 Community Regular

sun33

Posted
Posted
If you have a problem with your MFD LCD screen (busted scan lines, bad backlight, bad pixels),

then replace it with this fresh new one. I've done it. I can verify that replacing it with this panel

works great. Requires removal of MFD, and careful dis-assembly of MFD, connect two ribbon cables,

and re-assembly. Takes just 10 minutes and a screwdriver.

$200 plus $9.99 shipping bubble wrapped in anti-static foam.

so is this genuine nissan one or after market?

cheers.

rtune Experienced

rtune

Posted
  • Author
Posted
so is this genuine nissan one or after market?

cheers.

As far as I know nissan do not sell the screen. They sell the entire MFD for mucho $$$s only.

the MFD is plastic surround and cage and buttons, the MFD circuit board with its various sensor inputs

and the toshiba screen.. this is just the screen.

rtune Experienced

rtune

Posted
  • Author
Posted
a little bit off topic but around how much would the real mfd cost approx?

I see a second hand one in pretty poor shape listed at 90,000 yen about to close.

so after fees and expenses that is pretty close to $2000 aud.

and, this screen is the "real" mfd, as in, if you have a busted screen, it is this

screen that is busted.

Just in case people think this is an inferior non oem substitute..

  • 1 month later...
BOBBYr34 Experienced

BOBBYr34

Posted
Posted
If you have a problem with your MFD LCD screen (busted scan lines, bad backlight, bad pixels),

then replace it with this fresh new one. I've done it. I can verify that replacing it with this panel

works great. Requires removal of MFD, and careful dis-assembly of MFD, connect two ribbon cables,

and re-assembly. Takes just 10 minutes and a screwdriver.

$200 plus $9.99 shipping bubble wrapped in anti-static foam.

Hi i am after a screen and you text me pls 0414959914

Thank you

  • 2 weeks later...
  • 2 weeks later...
CR34M Community Regular

CR34M

Posted
Posted

If anyone knows where you can get the whole MFD (with casing etc) will buy it off you...or from Nissan itself lmaa i really dont mind spending the money its better than going aftermarket and getting an Alpine screen for example which costs a shitload and doesnt even fit the factory center console on my GT...

Adrian P Community Regular

Adrian P

Posted
Posted

There was 2 types of screens used in the GTR mfd, the early models used a Sharp screen, and the late models used a Toshiba screen. (as far as I know there was a supply issue with the Sharp LCD, thats why it got changed.) From what I can figure out the Nismo GTR MFD2 Unit will accept either LCD as there are both the connectors.

Make sure your GTR screen has 2x ribbon cables going to the LCD, a skinny ribbon cable and wide ribbon cable (Toshiba), or if it as 1x 30pin cable it a Sharp screen and will not fit!!

I am currently experimenting with both types of unit and will be putting up an in depth post in future...

fantov Enthusiast

fantov

Posted
Posted

Hi Mate,

I've got a 99 34GTR with the annoying white tram lines going through the RHS of the MFD... Can you pls confirm the toshiba screen your selling is a direct replacement for the early model 34 GTR's!

... If so can you pls put me down for one

will PM you

  • 2 weeks later...
uae810 Newbie

uae810

Posted
Posted
If you have a problem with your MFD LCD screen (busted scan lines, bad backlight, bad pixels),

then replace it with this fresh new one. I've done it. I can verify that replacing it with this panel

works great. Requires removal of MFD, and careful dis-assembly of MFD, connect two ribbon cables,

and re-assembly. Takes just 10 minutes and a screwdriver.

$200 plus $9.99 shipping bubble wrapped in anti-static foam.

hi ... i would like to order 2 screens .heat busted mine and my friends. the problem is i cant pm u over here... could u email me on [email protected] .thanks

  • 2 months later...
mole34 Apprentice

mole34

Posted
Posted

hi there, just wondering if you have any screens left?

My one is heat damaged and realy sh@#s me. please email me as i can not pm.

thankx heaps.

[email protected]

cheers.

  • 5 months later...
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Well, this is probably where a wiring diagram and a multimeter come into play.
    • Jarsky
      gauge needle removal

      By Jarsky · Posted

      I can say to anyone thats doing this; having done a number of R clusters; just be careful if its an unknown cluster.  It takes a bit of force to pull up; but if it feels excessive then its probably stuck. I've had this and pulled the entire hair spring out; and I can tell you; its not easy getting the correct spring replacement with the correct inner diameter and winding. In my case someone had used some sort of adhesive to stick it to the spindle and it pulled the whole spindle out; which the force seperated the hairspring from the spindal and caused it to deform.  You may have to clean it (IPA); or in my case if i'd known i should have used some sort of solvent on it.  Also check out Cruizin Central on eBay. He does all sorts of dials; and you can email him with any custom designs you want. So if you want like certain logos etc...he'll send you a mock of what it will look like then you accept the order and he'll take care of the rest. Fantastic dials and he can do basically any design you want. 
    • Jarsky
      R33 GTST Axles

      By Jarsky · Posted

      Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
    • Jarsky
      R34 Speedo not working after manual swap

      By Jarsky · Posted

      Ive converted a few clusters for the R33 with 320km/h dials. On the back there are some pads which can be bridged or unbridged (using solder or wick braid) to calibrate it. There is one bridge which is for MPH <> KPH; and there are combinations of bridges to offset it. There is probably a diagram  For example; this is my conversion for a 180km/h dial to a 320km/h dial (I put custom GT-R dials on it with the GTS25t layout) If you have J2 soldered (assuming the S clusters have a similar config to the R clusters); you may need to remove that solder
    • Rezz
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By Rezz · Posted

      Back on topic 😉, these are some of the notable pages from the booklets that are supplied with each weekly parts update. I never knew the BNR32 test mule car had an S13 Silvia front end... *Edit: On closer inspection the test car still had the R32 body, but only the front end had Silvia panels etc.
×
×
  • Create New...