Jump to content
SAU Community

Recommended Posts

Well as you know i have run a bearing in the GTR.....

I reali have a few choices.....

Im trying to save for a house and really at the moment thats the most important thing....

So i can rebuild the enigine.... $10,000....

I could try and sell the car as is.... What would it be worth? Leaving the wheels, power Fc etc etc etc?

I could strip the car get it back to standered and sell it? Whats it worth then?? And then sell the parts serperate?

Or lastly i could get a rb26 engine for 3000 and put it in my self and sell it... Whats it worth then??

These are just ideas at the mo.. Just tossing up what to do....

Then id get a cheaper car around $10,000 as a daily

Help

Link to comment
https://www.sau.com.au/forums/topic/256567-need-some-advice-what-do-you-think/
Share on other sites

  • Replies 54
  • Created
  • Last Reply

Top Posters In This Topic

Strip parts, new RB26 put the work in and put your parts into new rb26 and sell the old one for cheap, or keep it incase you need to use other stuff off of it. But a cheap daily for like $2k while all this is happening if you don't already have one

I have a whole list of parts thats only done around 1000kms if that...

SARD injectors

Power FC and Controller

Jun Cam Gears

Greedy Profec 2 Boost Controller

Brand New in Plastic Nismo Fuel Pump

Work Xd9s 18 x 10 Brand New Tyres

HKS boost Gauge

Pod Filters (or Standered Air Box)

Thats just the stuff i could replace for standered

Edited by Adz2332
I have a whole list of parts thats only done around 1000kms if that...

depending on size, bout $1000 SARD injectors

$1300 Power FC and Controller

$250? Jun Cam Gears

$350 Greedy Profec 2 Boost Controller

$250? Brand New in Plastic Nismo Fuel Pump

$3000 at least Work Xd9s 18 x 10 Brand New Tyres

$150-200? HKS boost Gauge

$100-150? Pod Filters (or Standered Air Box)

thats approx 6k - 6.5k worth of parts!

Thats just the stuff i could replace for standered

there 700cc injectors

But yer it is roughly that sort of cash in parts...

so if i was selling the car for 24,000 get 6000 for parts get back 30000.....

have to out lay right now around $4000 to get an engine but it in and replace back to standered parts tune etc...

and have a few other little things,

Second blank GTR key,

Brand new Greedy Strut Brace

Brand new Greedy Radiator air guide

Carbon N1 wing

GTR Carbon end caps

Full Exhaust system

Edited by Adz2332

yeh id just slap another rb26 in there, the car is worth bugger all sold with a dead donk. like has been suggested, replace with stock rb26, sell off all good parts from your dead motor and that will more than cover costs

well i am looking for a greddy front strut brace

and i would rather help a fellow sauer out...you know what i mean

wont be much but will be something

so first dibs on the strut brace

well i am looking for a greddy front strut brace

and i would rather help a fellow sauer out...you know what i mean

wont be much but will be something

so first dibs on the strut brace

seagull03.jpg

:huh:

if you ever think about owning a GTR again you will potntialy still have the same problem, and no matter what engine you buy it'll still have the same design flaws unless you fix it... so i say fix this one up if you still want to drive an import, otherwise, sell it and buy some non-turbo local car =P

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • also possibly backed up to my filler and shat down it! 🤣
    • Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...