Jump to content
SAU Community

Tapping For New Tensioner On Rb25-30

joe blo

By joe blo,
in Engines & Forced Induction

 Share

Recommended Posts

Guishnu Enthusiast

Guishnu

Posted
Posted

Not done it myself yet, but i believe that it doesn't matter how far you drill in (within reason) mainly because if you hit the water jacket, you just line the thread with plenty of locktight when you put it in. This is all off the top of my head and i have not researched it recently tho. Will be doing it myself again shortly.

With regards to the position, i don't think there is any measurable correct position. It's a tensioner, not an idler - so any slackness in the belt can be taken out.

SATO GTS Community Regular

SATO GTS

Posted
Posted

There is only about 5 to 7 mm wall thickness in the block at the section you need to drill into. It does not matter if you go it to the water gallery as it will seal up when you put the stud in with loctite or sealant.

If it's within a certain area going of the manual that has been produce by ppl of this forum then you will have no problem.

There is 1 point that I can not emphasize enough, that is for the thread to be tapped straight and true so that the belt runs inline with all the pulleys and doesn't foul on any thing to detoriate the belt and cause premature wear.

brada31ke70 Enthusiast

brada31ke70

Posted
Posted

i have a rb30 out of a series 3 silloette, just tapped the hole 16mm down from the head and 27mm in from the little 5mm hole, drilled in about 10-12mm and did not hit the water jacket, but if you do, use thread seal tape or even better, some hemp, lock tight will not work at all. it is best to tap it straight but if it is a little off, when you do up the tensioner it will pull it straight between the machined area of the block and the back of the tensioner. i used a 26 tensioners, not sure if it is different to 25.

  • 4 weeks later...
mongor Contributor

mongor

Posted
Posted
There is only about 5 to 7 mm wall thickness in the block at the section you need to drill into. It does not matter if you go it to the water gallery as it will seal up when you put the stud in with loctite or sealant.

If it's within a certain area going of the manual that has been produce by ppl of this forum then you will have no problem.

There is 1 point that I can not emphasize enough, that is for the thread to be tapped straight and true so that the belt runs inline with all the pulleys and doesn't foul on any thing to detoriate the belt and cause premature wear.

haha yeh word to that! i took so much time drilling and tapping my block and when i had finished, the tensioner had like a 0.2mm gap on one side wich made me freak out thinking my timing belt would jump straight off and drop valves... so i put a 3/8 deep reach socket over the stud ( once it was sealed in the block) and gently tapped it until it was straight. The ceff has done about 5000 k's now and it hasn't gone bang yet! : )

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Ozdavroz
      ATCC Amaroo Park 1987

      By Ozdavroz · Posted

      Yep that's pretty much what I want to see. Racecars that look and sound like the Group A but with newer tech underneath to make them faster and safer. I'm sure there's enough VK-to-VN commodore, E30 BMWs and Foxbody mustangs shells around to make up a decent number of cars with hopefully a couple of sierras, rx7 and R31s in there too. 
    • robbo_rb180
      WTB RB25 Gearbox NSW / central west

      By robbo_rb180 · Posted

      Contact Jessestreeter.com/Skevas Racing/JustJap for a new r34 rb gearbox or go a cd00# conversion. No point playing with unknown condition gearboxes.
    • robbo_rb180
      ATCC Amaroo Park 1987

      By robbo_rb180 · Posted

      Such a shame places like Amaroo Park have been redeveloped, smaller tracks always make for good racing. Cheers for sharing @PranK there's some good Lakeside video's too. Its so hard with older the cars as parts are so rare and everything was made for a particular chassis at that point in time. Even the V8 Supercar Blueprint era cars are all different between each chassis within a team as they learnt things and made improvements. The COTF cars between each Chassis builder is different too especially motor/oil systems/intakes. The Group A stuff is worth so much too especially chassis with good history. The only way to do it would be composite panels and similar engine drivelines to the original cars. Ford sierra running Focus RS driveline, Commodore running a short stroke LS/LT or a Falcon with coyote and a H Pattern dog box. Could use a standard ecu across all models with a Torque Map and DBW for parity which is not even used in Supercars currently. Hell a TCM is almost a full chassis car these days and the suspension is not even close to standard style in the front running cars.  
    • Commsman
      spot the stagea

      By Commsman · Posted

      Dashcams Australia (13/05/25) captured JDMHSE (Vic plate) being a right tosser. 
    • Ozdavroz
      ATCC Amaroo Park 1987

      By Ozdavroz · Posted

      Wish someone would start a racing series for Group A replica cars, a bit like Touring Car Masters but for 1985 onwards and not grandpa's falcon and/or Monaro. I know they race in some historic class but that's for original cars, no replicas allowed.
×
×
  • Create New...