Jump to content
SAU Community

Failed Epa Test Need Help...

i2icho

By i2icho,
in Victoria

 Share

Recommended Posts

BeEnAr Experienced

BeEnAr

Posted
Posted (edited)

OK you got it all wrong. The hose that is attached to the T now, put that it the top of the solenoid. Get a new hose and put it going from bottom of solenoid to the T piece. then you are all sorted.

Edited to say - Sorry I just realised that my pic is not showing you the colours etc when enlarged. I will upload again for you if you still having probs.

Edited by Dirk Diggler
W0rp3D Grand Master

W0rp3D

Posted
Posted
OK you got it all wrong. The hose that is attached to the T now, put that it the top of the solenoid. Get a new hose and put it going from bottom of solenoid to the T piece. then you are all sorted.

Edited to say - Sorry I just realised that my pic is not showing you the colours etc when enlarged. I will upload again for you if you still having probs.

So as the diagram says the bottom goes to the T, but which one then goes to the wastegate and where does the other one go?

W0rp3D Grand Master

W0rp3D

Posted
Posted
cheers all sorted just gotta go down to bursons for some vacuum hose and its all good, thanks for all your help

much appreciated

ben

Just for the record which hose went to the wastegate and where did the other one go?

i2icho Enthusiast

i2icho

Posted
  • Author
Posted
Just for the record which hose went to the wastegate and where did the other one go?

Bottom of solenoid conects to the T peice which connects the Intercooler and the wastegate

where the top solenoid conects to the piping running under the I/c pipping which i belive is the C.Converter

post-26040-1234682487_thumb.jpg

W0rp3D Grand Master

W0rp3D

Posted
Posted

Just had a look at some piping i have here, do you mean the vac line goes into a metal pipe that then goes into the pipe between the air flow meter and the turbo?

If that is correwct then that pipe is the return pipe for the blow off valve.

i2icho Enthusiast

i2icho

Posted
  • Author
Posted
Just had a look at some piping i have here, do you mean the vac line goes into a metal pipe that then goes into the pipe between the air flow meter and the turbo?

If that is correwct then that pipe is the return pipe for the blow off valve.

yeah thats right? runs kind of underneath the I/C pipping, wasnt to sure exactly what it was but yeah that sounds right.

Got some Vacc pipe from Auto Barn the guy just gave it to me and said there was no point in charging out 10cm so that was good.

boosts back to stock about 5-7 psi, so all should be good now

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy 路 Posted

      The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr 路 Posted

      Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Marek
      Hi everyone.

      By Marek 路 Posted

      Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 馃槈. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 馃槏.
    • Marek
      WGNC34 - floor mats

      By Marek 路 Posted

      Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 馃檹 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 馃槈. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 馃槏 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • ARB26
      S1 Autech 260RS Wiring Diagrams

      By ARB26 路 Posted

      I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
脳
脳
  • Create New...