Jump to content
SAU Community

Recommended Posts

Got a set of ku36 a few weeks ago from local tyrepower shop in Albury.

Prices were as follows

235/45 -$200

255/40 -$285

245/45 -$245 no stock at the time

Hey Luke,

Thanks for the info. Good prices there, but after factoring in freight and fitting costs, its probably no real saving to buying them locally unfortunately. How do you find the Kumho's? Im thinking about getting a set for the road now anyway.

Edited by SLVR32GTR

I have Kumho KU36 on my Supra because I track it fairly regularly and only have one set of rims. Good tyre for what they are, but they're not a semi slick. I use 245/40 and 275/35 * 18. I've done 2 Lakeside Sprints, 1 QR Sprint and probably 5000km of street driving since Sept last year.

On the road:

they're not loud, good in the wet, but tramline alot (I run a fairly agressive alignment too so its hard to say how much of that is caused by the tyre).

On the track:

- Only really good for about 3 laps before the rears go off. This is on my Supra remember, and my rears get a fair workout from my driving style... Might last a bit longer on an AWD car. I'm careful not to warm them up too much on the warm up lap as they work best just off cold. That's not to say they're better than a cold semi slick - they're not.

- They need alot of pressure like a street tyre. I run between 36 and 40psi cold. I found there was no point aiming for a target hot pressure because by the time they get hot, they're past their best. Better off aiming for a hot lap straight off the cuff with these tyres. Mine generaly come on the 1st or 2nd flying lap. byt he end of the 3rd lap you have to start being a bit more careful with the right foot.

I'm really happy with them on the Supra. If you only had one set of rims and wanted a jack-of-all-trades tyre,I'd recommend them. Or if you just want them as a really good street tyre and aren't really concerned about wear, then yeah go for it.

Edited by hrd-hr30

Thanks for the info Harry.

I just talked to Alan at Z Car Workshop here in Briz and i can get the following prices for Silverstone Tyres

FTZRR in 235/40 (largest in 17) for $375

s585 for slightly less than $375 (no exact price)

Am going to go and have a chat to him tomorrow hopefully and see what they are like, as i havent heard or read much about them.

Try Track side tyres in melbourne. Craig is the man to deal with. 18 months ago we could get RE55's landed in townsville for 420 each for 255 17s. Very helpfull and if i was not getting toyo 888s cheap through my friends shop I'd use him agian for sure. Obviously with the exchange rate they won't be anywhere near that now but his service was outstanding.

I have only run them at a winton fun day so far, sprints start again in a few weeks.

Like Harry said tramlining can be a problem, but overall i'm really happy with them.

Harry how have you found the tyre wear so far?

Tony,,,I really don't know much about which tyre you should use,,,but what I will tell you is very simple.

If you want to go fast at hillclimbing you have to use the softest tyre you can find. Grip on cold tyres is what it's all about.

It's no secret that all the libre/sports sedans run avon slicks,,,why,,,because there's no way you are going to get heat in the tyres,,,so the only other way to get grip is a softy.

If I was using a Skyline for cllimbing and had a spare set of wheels I would buy a durometer and start testing tyre hardness.

The only problem is they will end up being hillclimb tyres only.

Neil.

Thanks for the replies guys. Because i want to use the car for track days as well, im going to have to compromise and go a med-hard tyre im thinking. I will keep ringing around and getting prices and info and see how i go.

  • 1 year later...

hi, there :happy:

1) what does tramline mean?

2) i have used Firenza Sumitomo before and they were fairly loud. How's road noise on the KU 36 compared to this?

3) does KU36 have some sort of "rim protection"?

thanks

On the road:

they're not loud, good in the wet, but tramline alot (I run a fairly agressive alignment too so its hard to say how much of that is caused by the tyre).

hi, there :)

1) what does tramline mean?

2) i have used Firenza Sumitomo before and they were fairly loud. How's road noise on the KU 36 compared to this?

3) does KU36 have some sort of "rim protection"?

thanks

1) follows the contours in the road

2) never driven on the Sumitomos, so i can't say

3) yeah, pretty sure they did

  • 1 year later...

hey guys,

i can get kumho ku36 or other semi slick tyres cheap as i work for a tyre company and get cost price for tyres if interested??

ku36 are a good semi slick tyre there much better on a awd car then a rear wheel drive.

thanx

hey guys,

i can get kumho ku36 or other semi slick tyres cheap as i work for a tyre company and get cost price for tyres if interested??

ku36 are a good semi slick tyre there much better on a awd car then a rear wheel drive.

thanx

I'd recommend A050's - softs are ok for just hillclimbs on road going R32 - too soft for supersprints - we find mediums have done the job on both R32 & R33 at all NSW, Aussie and time attack events.

Tow out on the front, bitta tow in on the back around 28psi cold.

Enjoy

hey guys,

i can get kumho ku36 or other semi slick tyres cheap as i work for a tyre company and get cost price for tyres if interested??

ku36 are a good semi slick tyre there much better on a awd car then a rear wheel drive.

thanx

id also recommened bridgestone re070 as a 22545r17 has a speed rating of w=270k which are a good tyre with the write alignment

They do not even compare to a proper semi like the AO50

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...