Jump to content
SAU Community

Recommended Posts

ive just finished builing my new single turbo setup with a t04z use to have twin t517zs making 511 hp on 22 psi

with the to4z it makes 353kws at 15psi as soon as you wind the boost up fom 15 psi it stops making the power goes back wards its like its hitting a brick wall

afrs are 12

ignitons not breaking down was thinking the cams are to small or the standard plume and throttle bodys could be doing it any help would be appreciated thanks tim

engine specs

built bottom end

pored head

tomei type b springs and cams

new guides

800cc injectors

m and w cdi ignition

haltech e11v2 with 3 bar map

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

cat/exhaust or wastegate?

the car has

no cat striaght pipe

three and a half inch from turbo back straight through exhaust

and a turbo smart 50mill pro gate

i think they should be up to the task

need some more info. What amount of ign timing? does the timing drop off very rapid once it hits the higher load point? Sounds like its running out of cam though. What specs are the cams. What comp ratio is the engine. etc.

Just throwing around some ideas.

need some more info. What amount of ign timing? does the timing drop off very rapid once it hits the higher load point? Sounds like its running out of cam though. What specs are the cams. What comp ratio is the engine. etc.

Just throwing around some ideas.

the timing is about between 32 at 5000 and 20 at 9000 the cams are 260 by 9.15 and the comp is 8.3

possibly a boost/exhaust leak then? have you checked all your piping, vacuum hoses, exhaust flanges and the rest?

theres no leaks checked every thing in the leak department ive also done a compresion test today and they are all between 120 and 122

the car has

no cat striaght pipe

three and a half inch from turbo back straight through exhaust

and a turbo smart 50mill pro gate

i think they should be up to the task

Have you dropped the exhaust from before the cat to be 100% certain?

Hmm. Sounds very odd. That turbo should be able to generate much more hp.

Any other mods done at the time of the turbo change or just the turbo change.

only the turbo gate and manifold and exhuast to cat all new and its also laggy compared to others on the forum should a t04z with a .82 split housing make 22 psi before 6000

Exhaust manifold design?

Where are the cams set also

the exhaust manifold is a 1.5 inch steam pipe equally length runner at 500 mill each and the cams are set to 0 on inlet and exhaust should such little cams be really lumpy

the manifold collector has to have all the runners peaked for good flow. How lumpy? will be a little lumpy.

Who is the tuner.

So many factors will cause lag.

Can give you the name of a really good tuner in the area, may be able to help you out

the manifold collector has to have all the runners peaked for good flow. How lumpy? will be a little lumpy.

Who is the tuner.

So many factors will cause lag.

Can give you the name of a really good tuner in the area, may be able to help you out

mark at mrc has been tuning it and he cant figure out why its not making power and why its so laggy he does a good job its lumpyer then the rb26/30 he tuned with 290 by 12 cams what do you mean by peaked

the car has no cat i dont run one as the car is a track car

I know that...

Well from where the "de-cat" pipe is, same spot, matters not... So i take it as a NO you have not tried the 10mins quick test to totally discount exhaust

All 6 runners merge into a peak and then into the turbo unlike some of them that have runners facing eachother.

Have you guys played with cam timing yet?

all the runner come to a point then into the turbo tryed playing with the timing on the old setup but didnt make much of a difference only moved the powerband around no gains from it whats the name of the tuner that you no thanks tim

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
    • I was able to get some underside photos while the car was on the ramp The suspension is all Altezza/IS200/IS300 so getting part's will hopefully be less of a headache
    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
×
×
  • Create New...