Jump to content
SAU Community

Recommended Posts

This is for the S2 guys, S1 might be the same, i don't know. when you push the door lock button on the drivers side door controlls, does it lock all the doors? mine locks all the other doors except for the drivers door?

Edited by QWK32
Link to comment
https://www.sau.com.au/forums/topic/258471-door-lock-button/
Share on other sites

the button on the window panel locks 3 doors. the drivers handle button is controlled by the keyless module.

manually pushing the drivers handle button locks all doors.

thanks chris, you might be able to tell me, where is the the lock and unlock signal wire for all four door, i can find the one that does the 3 doors and boot, but not the signal for all four?

how does the signal from the key, lock the drivers side door? i'm guessing the other doors lock once the drivers side one does.

I'm not going to tell you but I will let you work it out. use the remote entry to close the door (close the door catch with a screwdriver) listen for the relays to click. working it manually you will hear one set of relays go. with remote you will hear two sets. find that set.

Where are these relays? I'm having similar issues with my aftermarket alarm only working pass front and both rears, and tailgate, but not drivers front door. I want the alarm to do all doors so I can swap over to a slim normal key, not the bulky factory key.

Cheers, Greg.

Where are these relays? I'm having similar issues with my aftermarket alarm only working pass front and both rears, and tailgate, but not drivers front door. I want the alarm to do all doors so I can swap over to a slim normal key, not the bulky factory key.

Cheers, Greg.

pm sent

Hi Ladies/gents,

I have been installing alarms in Sydney for 8 years,

Central locking relays/wires are located behind the glove box.

Remove the glove box and on the left behind the dash you will find a blak box with a plug. I cant remember off the top of my head what the colours were.

This is where i get the lock/ unock pulse for my S2. This will work for 4 doors plus rear hatch.

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
×
×
  • Create New...