Jump to content
SAU Community

Where To Mount Alpine Type-r (spr-17s) Tweeters In R34

The_Scroop

By The_Scroop,
in Car Audio & Electrical

 Share

Recommended Posts

The_Scroop Enthusiast

The_Scroop

Posted
Posted

Heyy

I've been gathering all the parts I need to put together a half decent sound system but I've run into a problem.

The tweeters for the SPR-17S type-r splits are massive. I have no idea where or how I am supposed to mount them into the car.

The doesn't seem to be a space (apart from right next to the door handle) that is wide enough to cut out and mount a tweeter.

Has anybody here had any luck? How/where did you mount the tweeters for your type-r splits.

Cheers

Dom

The_Scroop Enthusiast

The_Scroop

Posted
  • Author
Posted

I had a read through the thread on the carbon fibre sail mount earlier, but I'm not sure if it would work for me because of the size. The type-r splits seem too big even for that.

Carbon 34 Grand Master

Carbon 34

Posted
Posted

mine fit just fine on the little triangles on the door near mirror R34 GTT, molding mine in carbon horns end of next week, photos posted up later on

they can fit in windshield posts as well of you ditch the housings, air vents(not blocking air either), door panels behind cloth trims, pull handles,or a few dozen other spots depending on the level of installers knowledge. and cost to do a trick install ???

for some installs you ditch the housings and might trim off the tabs a bit with dremel, only do if your a pro or confident installer?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      33 GTR Broken front wheel knuckle

      By MBS206 · Posted

      Let's be honest, most of the people designing parts like the above, aren't engineers. Sometimes they come from disciplines that gives them more qualitative feel for design than quantitive, however, plenty of them have just picked up a license to Fusion and started making things. And that's the honest part about the majority of these guys making parts like that, they don't have huge R&D teams and heaps of time or experience working out the numbers on it. Shit, most smaller teams that do have real engineers still roll with "yeah, it should be okay, and does the job, let's make them and just see"...   The smaller guys like KiwiCNC, aren't the likes of Bosch etc with proper engineering procedures, and oversights, and sign off. As such, it's why they can produce a product to market a lot quicker, but it always comes back to, question it all.   I'm still not a fan of that bolt on piece. Why not just machine it all in one go? With the right design it's possible. The only reason I can see is if they want different heights/length for the tie rod to bolt to. And if they have the cncs themselves,they can easily offer that exact feature, and just machine it all in one go. 
    • Bennym35
      New guy

      By Bennym35 · Posted

      The roof is wrapped
    • Duncan
      R34 GT-T cycling ABS pump

      By Duncan · Posted

      This is how I last did this when I had a master cylinder fail and introduce air. Bleed before first stage, go oh shit through first stage, bleed at end of first stage, go oh shit through second stage, bleed at end of second stage, go oh shit through third stage, bleed at end of third stage, go oh shit through fourth stage, bleed at lunch, go oh shit through fifth stage, bleed at end of fifth stage, go oh shit through sixth stage....you get the idea. It did come good in the end. My Topdon scan tool can bleed the HY51 and V37, but it doesn't have a consult connector and I don't have an R34 to check that on. I think finding a tool in an Australian workshop other than Nissan that can bleed an R34 will be like rocking horse poo. No way will a generic ODB tool do it.
    • GTSBoy
      33 GTR Broken front wheel knuckle

      By GTSBoy · Posted

      Hmm. Perhaps not the same engineers. The OE Nissan engineers did not forsee a future with spacers pushing the tie rod force application further away from the steering arm and creating that torque. The failures are happening since the advent of those things, and some 30 years after they designed the uprights. So latent casting deficiencies, 30+ yrs of wear and tear, + unexpected usage could quite easily = unforeseen failure. Meanwhile, the engineers who are designing the billet CNC or fabricated uprights are also designing, for the same parts makers, the correction tie rod ends. And they are designing and building these with motorsport (or, at the very least, the meth addled antics of drifters) in mind. So I would hope (in fact, I would expect) that their design work included the offset of that steering force. Doesn't mean that it is not totally valid to ask the question of them, before committing $$.
    • Kinkstaah
      R34 GT-T cycling ABS pump

      By Kinkstaah · Posted

      The downside of this is when you try to track the car, as soon as you hit ABS you get introduced to a unbled system. I want to avoid this. I do not want to bleed/flush/jack up the car twice just to bleed the f**kin car.
×
×
  • Create New...