Jump to content
SAU Community

Recommended Posts

researching this now. if there is an interest then I'll go ahead with it. box that I intend to use WILL play movies as well. it will use the OE screen and I'll make a blanking plate for the OE controls.

rough costing is in the $1-2K mark and will cover both generations.

I have a full replacement solution in the works as well. more info on that later.

so do I have interest?

Link to comment
https://www.sau.com.au/forums/topic/259714-touchscreen-navi/
Share on other sites

it would be a all in one box. no splitting it up. I have the other unit here now. picked it up this morn.

it would be a rework on some of the cars.

rianto. it would fix your volume issue as well ( I now have a FULL navi setup out of an 03 so thats what I'm basing this on.)

Danny (sydney)

its still at concept stage - not likely to go into production for at least 8-12 months. in that time I'll probably rework it 3-4 times to get it stable. so if you are going to buy a car based on this alone - dont.

Edited by Chris Rogers

its a full rework unless I can get more info on the GVN53 units. garmin aren't too forthgiving with that info..

current box I have in mind is entirely different. overlays are proving to be a pain as the early screens ARE NOT a true 7" screen.

ok - using the OE screen is out as far as I'm concerned. size of screen (6.9" diagonal) stops me from finding an overlay that fits. I can get one done but at $800 a shot and a minimum of 5000 I dont see it happening for the 2001-2004 cars.

I do have a rough price on the replacement system (box only no screen) and that comes in at $2kish loaded.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
    • Shimmed or shimless, still solid, no hydraulic pump up stuff.
    • They have said food will be limited. Mainly meat pies and sausage rolls from memory. But they have a coffee van!
×
×
  • Create New...