Jump to content
SAU Community

Recommended Posts

NISSAN SKYLINE R33 GTS-T S1 M-SPEC

ENGINE:

RB26DETT conversion

RB26 sump w/transfer case sliced off

RB25 engine mounts

RB25 Harmonic balancer

HKS Intercooler

BLITZ front pipes

SIGNAL straight through carbon muffler

HKS Pod filters

Splitfire coil packs

TODA Racing clutch

TODA Racing 4.5kg Flywheel

CUSCO 2 way mech diff

IRIDIUM Plugs - 6's

R33 GTR fuel pump

SUSPENSION / BRAKING AND HANDLING:

SELBY rear 28mm sway bar

RACING GEAR coilovers

D1 rear camber arms

D1 HICAS lock

CUSCO front tension rod

Solid rear subframe bushes

D1 adj castor rods

PROJECT MU Slotted front rotors

TRW (LUCAS) brake pads all round

NISMO Front strut brace with brake stopper

GTR rear strut brace

BODYWORK & INTERIOR

Full body respray in Blood Orange

Satin Black bonnet and wing

SPARCO bonnet pins

NARDI Steering wheel

TRUST gear knob

SPARCO Spirnt drivers seat w/ BRIDE Rail

GReddy Profec B Spec II boost control

GReddy Turbo Timer

New Carpet

GReddy Boost Gauge

engine has spun a bearing , have R33 GTR Bearings to go on the engine

also have R33 GTR Crank that has been linished and polished with oil galleries filled with grub screws

R33 GTR Pistons & Rods

R33 GTR Oil Pump (Rebuilt)

Possibley interested in trades

Price $14,000 ono

bhmqt.jpg

would have more pics but GPU in my pc has died so i cant access the hard drives for now.

Link to comment
https://www.sau.com.au/forums/topic/260151-my-r33/
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...