Jump to content
SAU Community

Crankshaft Grinding

TriniGT

By TriniGT,
in Engines & Forced Induction

 Share

Recommended Posts

TriniGT Experienced

TriniGT

Posted
Posted

Hi people, once again I have a question. I got a second hand crank from a friend that replaced it for his build, it is an R34 crank 05U on the crank and the engine had a spun bearing. I got the crank checked and the machine shop said that they may have to remove .010-.020 on the rod journal and at the same time do all to measure up. They said that the mains are all fine, what I want to know is if I have the crank ground can I get rod bearings that are .020 oversize? I spoke to one person and they told me that they only come in .010" nothing more, do I have an option for bigger sizes in the rod bearings? Let me know ASAP so I can know if I need a next crank, reason I took the crank in the first place is that it already had the long snout.

Jason.

Link to comment
https://www.sau.com.au/forums/topic/260887-crankshaft-grinding/
Share on other sites
SteveL Mentor

SteveL

Posted
Posted
They said that the mains are all fine, what I want to know is if I have the crank ground can I get rod bearings that are .020 oversize?

The journals are undersize when the crank is ground, but anyway I'm fairly sure the first undersize available is .025, so you should be fine. Someone else will be able to confirm or otherwise.

skidkid Proficient

skidkid

Posted
Posted

I've ground a few cranks before. Did you have crank checked for straight aswell because I reckon you would be real lucky if crank wasn't bent. Means it will require a grind all over if not to bent. Doesn't your machine shop supply bits? Have you googled for 'ACL bearings' site?

TriniGT Experienced

TriniGT

Posted
  • Author
Posted

Yes I was looking on the ACL site but I wanna make sure that I can get the bearings before I go ahead and begin the repair process. Seeing that people are suggesting it is possible to fix it then I will go ahead and get it done and order a set of bearings based on the size after machine work. This is going on a spare RB26DETT that I am going to be building up. It is getting some CPs and rods. Will let you know how it goes and I will contact ACL tomorrow to get a definite answer.

bubba Grand Master

bubba

Posted
Posted (edited)

Best to get the bearings your machinist suggests, then give them to him BEFORE he grinds your crank, that way he can mic up that specific set of bearings and grind to suit.

Edit: 1pm Friday here.. and I knock off in an hour :D:banana:

Edited by bubba
murrayis Mentor

murrayis

Posted
Posted

http://www.aclperformance.com.au/NissanRB26DETTBearings.htm Is the link you want, the bearing sizes are metric.

First line of sizes is STD then 2 oversize bearings to suite a ground crank.

But like the others said get the bearings they recommeneds then take them to them and get them to machine the crank to suite the bearings.

T04GTR Grand Master

T04GTR

Posted
Posted

acl do 10 and 20 thou in race series, ndc do them up to 30 thou. just look at sr20 ones, there the same. just have to buy 2 sets..

you can also have it offset ground to remove less but give a 10 or 20 thou stroke increase wich is f**k all.

TriniGT Experienced

TriniGT

Posted
  • Author
Posted

Thanks a lot for the responses. Should I worry about removing the nitride coating on the crank. I have read that removing the coating causes the bearing to spin very easy, can someone confirm that has ground their crnak and has been running it for years?

TriniGT Experienced

TriniGT

Posted
  • Author
Posted

Just got confirmation that the crank is bent and that it can straighten it and the mains will have to be ground .010" and the rod journals .020". Your thoughts on this and has anyone ever heard of straightening the crank, the shop said they have a unit specifically used for this process. This is news to me.

skidkid Proficient

skidkid

Posted
Posted

I have straigtened a few with success and broken a couple aswell. You may be lucky. Make sure they cracktest it for you before they grind it!! Never used to worry about re-nitriding and don't think it caused a problem. The decision to go ahead rests with you though!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      By popular demand.. it was a coil. Got my hands on 1 new OEM coil, replaced with the one that made the less noise difference when I unplugged it while the car was running and started the car up. No stutter and the engine light was gone. I guess I’ll buy the other 5 they have lol
    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      PXL_20250828_063541093.TS.mp4
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
×
×
  • Create New...