Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

ppg = gearbox

ppi = plastic piping industries

RSL= return services league

YMHBJAIBHLN = your mum has big juggs and i banged her last night

oh getting off track here... soz

ppg = gearbox

ppi = plastic piping industries

RSL= return services league

YMHBJAIBHLN = your mum has big juggs and i banged her last night

oh getting off track here... soz

How is ppg = gearbox ? I can understand the jugg reference however.

So in answer to your question

No. My mum doesn't have big juggs.

How is ppg = gearbox ? I can understand the jugg reference however.

So in answer to your question

No. My mum doesn't have big juggs.

you are making me think of jake from two and a half men... really slow to uptake...

ppg make gearbox's and are commonly used in skylines for a drag racing application...

as this is a whoretown, nothing needs to make sence...

so if i say your mum has big juggs then thats what shes got...

you are making me think of jake from two and a half men... really slow to uptake...

My reputation proceeds me.

And no ppg isn't like juggs nor tpg. Tpg is a company selling intertrons. I bought three of them.

nothing needs to make sence...
1. sence

1. This is how idiots spell sense, since they have no sense, they can't f**king spell it.

2. This misspelled word is also a form of since according to some idiot - English translations.

<insert any MMORPG here> chat:

Idiot: That doesn't make sence!

Me: YOU don't make sense! "SENCE" IS NOT A f**kING WORD, MORON! Sorry... IDIOT! Wait, no... too subtle... how 'bout, nub to life!?

Edited by Isola
yeh, had the same crap happen with tpg

usually they aren't too bad.

meh

we had a tpg fail this evening too, glad we were not the only ones!

Seemed to be pretty much australia wide. I was hoping for the zombie apocalypse

as this is a whoretown, nothing needs to make sence...

so if i say your mum has big juggs then thats what shes got...

Truth.

And no ppg isn't like juggs nor tpg. Tpg is a company selling intertrons. I bought three of them.

THREE! I think that must have been their entire supply for a year

*Insert spelling Nazi shiz here*

I'm dissapointed in you John, you're slipping:

i am bender please insert gurder

*girder

P.S. Morning Mangs. Anyone got any steering column unis lying around?

Edited by Smity42

Sup mangs. Accidentally printed a defect report 65k pages long. oops. Cancelled it by the time it printed about 300 pages though. Small win?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...