Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

Yeah another negative. But it has been fairly disappointing there for the past 3 or 4 weeks now. With employees anyway.

I am dissapoint, I was all keen for hot youngness, but no!

sup Ravbat. Ice cream was average. Shitty milkshake and retarded employees. But shit happens. Hating work also.
dont forget that they were in no way hot!

Finally time for northside meet spot instead??

Hey mangs. Was stuck out working again, hence another no show last night.

Some pics from the southside meet. Night was spent laughing at the flat cappers.

post-178202-12875809756337510.jpg

post-178202-128758104725009176.jpg

post-38577-1287644541968881557.jpg

post-38577-12876448501192591626.jpg

post-38577-12876449572093404159.jpg

post-178202-12875809751260026568.jpg

Edited by SABBAi

Yo fellows,

Has anyone got a RB 20 coil pack loom or one that's interchangeable?

or know of someone that can replace the clips on the end?

Finally time for northside meet spot instead??

fuck your face

Yo fellows,

Has anyone got a RB 20 coil pack loom or one that's interchangeable?

or know of someone that can replace the clips on the end?

Martin has one. I know this because I stole it, and it's at my house.

I need a coil pack loom (and coil packs) that more or less work well enough to run a car...

Other than that, I'm not fussed. Would be nice if John came and undid all the damage he's done though :ermm:

Edited by Smity42
I need a coil pack loom (and coil packs) that more or less work well enough to run a car...

Other than that, I'm not fussed. Would be nice if John came and undid all the damage he's done though :)

Oh :ermm:

okay next offer. ;)

I need a coil pack loom (and coil packs) that more or less work well enough to run a car...

Other than that, I'm not fussed. Would be nice if John came and undid all the damage he's done though :ermm:

You home tonight, Mang? Lyss is going to Zumba at 7, so I could come up and fix it if you want.

You home tonight, Mang? Lyss is going to Zumba at 7, so I could come up and fix it if you want.

Zumba!

There's a BnR in albany creek in front of the coles, I'm not sure if it's open late thursdays though.

Yo fellows,

Has anyone got a RB 20 coil pack loom or one that's interchangeable?

or know of someone that can replace the clips on the end?

you can buy the ends new... repco can order them in or visit your local auto-elec...

Its a simple replacement, just takes a few minutes and careful hands...

Much easier to do when the loom is out of the car, just remove the coil pack piece and work on a table away from the car (help with back bending etc)...

You could take the loom to an auto-elec also to get them to replace the ends if you want...

If I remember correctly they were about $12-14 each

There's a BnR in albany creek in front of the coles, I'm not sure if it's open late thursdays though.

Tis open til 8pm Thursdays...

My neighbor owns it... I was there last night at close (hence how i know)...

A little uneccesary..... but always welcomed :ermm:

You like a f**k face?

Zumba!

There's a BnR in albany creek in front of the coles, I'm not sure if it's open late thursdays though.

I'll just keep hounding CH until they get their shit together.

P.S... could you teach me how to play guitar scales/solos/lead etc?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...