Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

When replacing my turbo, what gaskets do I need?

I'm thinking:

Manifold-> turbo gasket

Turbo->dump gasket

Oil return gasket?

Am I right that the oil feed doesn't need one?

Manifold-> turbo gasket

Turbo->dump gasket

These. Althought they are fairly sturdy gaskets and if they are in good nick you might be able to re-use your current ones.

Oil return gasket?

Should just be able to remove the oil return hose so shouldn't need a new gasket here.

Am I right that the oil feed doesn't need one?

You should replace all the banjo bolt washers on the oil feed/water feed/water return. That said, a lot of people probably don't bother, but they are not very expensive so I would.

Just take the banjo bolts to enzed or something and ask for banjo washers to suit.

What exactly IS a banjo bolt?

TJ-SS07.jpg

There will be one on each end of you oil feed line, water feed line, and water return line. So 6 banjo fittings, needing a total of 12 washers. The sizes will vary, (some will be the same some different) so you will need to work out the sizes you need when you pull it off and then take them in and say "I need 4 of these ones, 8 of these ones..." etc.)

The oil return line is just a normal clamed hose. I can't remember 100% but I think the gasket you are talking about for that one is where the hose fitting connects to either the block or the turbo. But you don't need to undo it there, just undo one of the hose clamps and take the hose off.

EDIT: That picture is a little misleading, the washers are not actually copper washers but 'banjo washers'. According to the dude at Enzed when I went anyway...

Edited by Smity42

Ok so I -might- be able to re-use those washers, depending on how they look when they come out?

Should I drop my oil before I do this? Or will it just be a small amount of oil that comes out of the feed?

I should drop my coolant though, yes?

Ok so I -might- be able to re-use those washers, depending on how they look when they come out?

Should I drop my oil before I do this? Or will it just be a small amount of oil that comes out of the feed?

I should drop my coolant though, yes?

You are NOT supposed to re-use the washers. They crush when you tighten the bolt and that is how they seal. Once crushed you are not meant to re-use them.

I think some people do though, but its a bit dodgy, and you may end up with leaks.

It might only be 31 owners that re-use them...

Should be no need to drop the oil, just let the car sit for a while so that most of it drains back to the sump before you do it. You may spill a small amount but nothing much.

Water... Can't remember. You will probably lose a fair bit of it so put a drain tin down, but theres probably no need to drain it entirely. Just fill it back up and bleed it when you're finished.

Been shut for a while for the airport link work. Maybe it was only through certain hours...

Did not know that. Must only be certain hours...

The oil return line is just a normal clamed hose. I can't remember 100% but I think the gasket you are talking about for that one is where the hose fitting connects to either the block or the turbo. But you don't need to undo it there, just undo one of the hose clamps and take the hose off.

I meant on the turbo where the oil return goes in (i think thats what it is, not sure) there's like a flat surface area around the hole - looks like it needs a gasket.

Burson have a turbo gasket kit with 2 metal gaskets and 'about' 4 cork ones for $50. No washers.

What's the enzed place you mentioned?

Edited by mosquitocoils

I meant on the turbo where the oil return goes in (i think thats what it is, not sure) there's like a flat surface area around the hole - looks like it needs a gasket.

Ahh... if there is something there that you have to transfer from your old turbo to your new that needs a gasket, then yeah you will need that.

Burson have a turbo gasket kit with 2 metal gaskets and 'about' 4 cork ones for $50. No washers.

NFI what those cork ones would be. Pics?

2 metal ones would me manifold-turbo and turbo-dump I reckon.

What's the enzed place you mentioned?

enzed (http://www.enzed.com.au/) or pirtek (http://www.pirtek.com.au/) or any other hose joint really. I didn't get a mobile guy out, I just went into a store.

been up in the copper today again, brisbane is a sea of activity...

people, cars, trucks everywhere...

seems business is back to normal for the major shopping centers...

hope the people who bought 20 loaf's of bread die eating them, wankers...

Ahh... if there is something there that you have to transfer from your old turbo to your new that needs a gasket, then yeah you will need that.

Yeah I'll just suss out what I need to re-use when I get to it I guess.

NFI what those cork ones would be. Pics?

2 metal ones would me manifold-turbo and turbo-dump I reckon.

Twas over the phone my good sir so no pics, but I was guessing the same as you.

So, good thing no one went to old Baskins last night...

XF and 33s would have gotten across that...

Are we allowed to pick women folk in the mens cricket team? I reckon this Elyse Perry chick bowls better than ANY of the blokes do...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Shouldn't need a "base map" for anything other than guidance to ignition tuning. You just need the engine capacity right, the injector size right, and something, almost anything, for a VE map. On an NA engine, fuelling is almost completely a function of load signal & rpm. It should run and drive with a completely flat fuel map. It will be too lean under load, but that's easily fixed. We used to tune all ECUs without any base map. There were no such things (until someone had tuned a near stock engine on one, and then they had a "base map".
    • What did you actually buy/how much did it cost? When I got mine in like.. 2017...? 2019? the aim was to run Torque for gauges via ODB2 and things like Track Addict/Laptimers/Dashcam/Reversecam/Spotify etc. Mine never broke, but I wonder if you've got the same needs (it sounds like it). Cause I liked the idea of being able to do anything with it. That said, yours also cost 3x the cost of what I spent so... food for thought.  
    • For me there is a massive difference in manufacturer or big brand crippled android (Sony, Kenwood etc) vs the sort of thing I've installed here, which is basically just a tablet in DIN form factor with open Android, and the other model of course is mirroring - Android Auto/Carplay. I hate the locked down manufacturer and AA options where they decide what apps I'm allowed to install, including the Launcher but also importantly things like Ecutek (for this car) or Real Dash (Stagea) are not supported. Plus those crippled versions tend to be slower due to both overheads and lower spec hardware. On the other hand, when this breaks I'll likely be in trouble for support....but how is that different to owning an Infiniti anyway
    • Yeah, Duncan is helping sell me back to Android devices. I've hated the whole Android head units due to their speed issues. Even in my old Hyundai Kona (2022 model), it behind the scenes was Android, and slow and shitty to start up. Once running wasn't bad, but still a good 15 to 30 seconds.
    • My roof rails are off atm on the E39 until the rust is fixed. I did find another little bit of surface rust under the rails when I took them off. As @soviet_merlin said I'd just leave them alone unless you're planning on ensuring they're properly sealed. I was on the fence about leaving them off as the delete is still a thing in BMW E39's but I feel like the car is missing something (er, it is, der) with them off and I'm looking forward to putting them back on.
×
×
  • Create New...