Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

In other news, oil and filter change on a VG30DET? Engine out.

do it from the bottom. get dan to toss it on a hoist.

did I see habib out at the downshift meet this afternoon?

couldn't see Noel anywhere, but looked like habib parked out by the entrance

spotted your 32 as I drove out of there in my toy car :action-smiley-069:

did I see habib out at the downshift meet this afternoon?

couldn't see Noel anywhere, but looked like habib parked out by the entrance

quite likely, he said he was gonna head there this afternoon. i was too...but then i would have missed the F1 :thumbsup:

did I see habib out at the downshift meet this afternoon?

couldn't see Noel anywhere, but looked like habib parked out by the entrance

It was indeed, we saw pwned and looked over the whole joint and couldnt find you.

I drove past that meet coming back home from bunnings, didnt realise it was on and was wondering where all the imports on granad road were coming from! Looked like a very good turnout.

It was indeed, we saw pwned and looked over the whole joint and couldnt find you.

I am only little and easy to miss

I didn't see your car until I was driving out so didn't know to keep my eye out.

Was a lot of cars out there. My car looked stock compared to some of the things rolling through.

I drove past that meet coming back home from bunnings, didnt realise it was on and was wondering where all the imports on granad road were coming from! Looked like a very good turnout.

They are claiming over a thousand cars. Not sure if there were that many (at least not all there at once) but there were a few hundred easily.

have to take the intake runner off to get the injectors

and the timing belt idler/tensioner mounts off that, so you have to take the timing belt off

in short:

filter change = engine out

injector change = engine in pieces

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...