Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

In other news, oil and filter change on a VG30DET? Engine out.

do it from the bottom. get dan to toss it on a hoist.

did I see habib out at the downshift meet this afternoon?

couldn't see Noel anywhere, but looked like habib parked out by the entrance

spotted your 32 as I drove out of there in my toy car :action-smiley-069:

did I see habib out at the downshift meet this afternoon?

couldn't see Noel anywhere, but looked like habib parked out by the entrance

quite likely, he said he was gonna head there this afternoon. i was too...but then i would have missed the F1 :thumbsup:

did I see habib out at the downshift meet this afternoon?

couldn't see Noel anywhere, but looked like habib parked out by the entrance

It was indeed, we saw pwned and looked over the whole joint and couldnt find you.

I drove past that meet coming back home from bunnings, didnt realise it was on and was wondering where all the imports on granad road were coming from! Looked like a very good turnout.

It was indeed, we saw pwned and looked over the whole joint and couldnt find you.

I am only little and easy to miss

I didn't see your car until I was driving out so didn't know to keep my eye out.

Was a lot of cars out there. My car looked stock compared to some of the things rolling through.

I drove past that meet coming back home from bunnings, didnt realise it was on and was wondering where all the imports on granad road were coming from! Looked like a very good turnout.

They are claiming over a thousand cars. Not sure if there were that many (at least not all there at once) but there were a few hundred easily.

have to take the intake runner off to get the injectors

and the timing belt idler/tensioner mounts off that, so you have to take the timing belt off

in short:

filter change = engine out

injector change = engine in pieces

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Messing around with. Twin kit for. Rb30/26  
    • For fuelling the Haltechs have O2WB fuel controllers. Very useful for helping tuning VE and correcting for *small* mistakes. Of course if your injector/cam/trigger/sensor data is just wrong (or for a GTT which is not a GT) then you will get impossible reactions to things. I am sure you know this already but the reason people don't typically put haltechs (or any Aftermarket ECU) on GT's is because there's practically no real gains to be had - So this knowledge won't be commonplace.
    • Can someone tell me if the cracks seen in the rear sway bar bushings in these photo's is unacceptable from a roadworthy point of view?  
    • Shouldn't need a "base map" for anything other than guidance to ignition tuning. You just need the engine capacity right, the injector size right, and something, almost anything, for a VE map. On an NA engine, fuelling is almost completely a function of load signal & rpm. It should run and drive with a completely flat fuel map. It will be too lean under load, but that's easily fixed. We used to tune all ECUs without any base map. There were no such things (until someone had tuned a near stock engine on one, and then they had a "base map".
    • What did you actually buy/how much did it cost? When I got mine in like.. 2017...? 2019? the aim was to run Torque for gauges via ODB2 and things like Track Addict/Laptimers/Dashcam/Reversecam/Spotify etc. Mine never broke, but I wonder if you've got the same needs (it sounds like it). Cause I liked the idea of being able to do anything with it. That said, yours also cost 3x the cost of what I spent so... food for thought.  
×
×
  • Create New...