Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

In other news, oil and filter change on a VG30DET? Engine out.

do it from the bottom. get dan to toss it on a hoist.

did I see habib out at the downshift meet this afternoon?

couldn't see Noel anywhere, but looked like habib parked out by the entrance

spotted your 32 as I drove out of there in my toy car :action-smiley-069:

did I see habib out at the downshift meet this afternoon?

couldn't see Noel anywhere, but looked like habib parked out by the entrance

quite likely, he said he was gonna head there this afternoon. i was too...but then i would have missed the F1 :thumbsup:

did I see habib out at the downshift meet this afternoon?

couldn't see Noel anywhere, but looked like habib parked out by the entrance

It was indeed, we saw pwned and looked over the whole joint and couldnt find you.

I drove past that meet coming back home from bunnings, didnt realise it was on and was wondering where all the imports on granad road were coming from! Looked like a very good turnout.

It was indeed, we saw pwned and looked over the whole joint and couldnt find you.

I am only little and easy to miss

I didn't see your car until I was driving out so didn't know to keep my eye out.

Was a lot of cars out there. My car looked stock compared to some of the things rolling through.

I drove past that meet coming back home from bunnings, didnt realise it was on and was wondering where all the imports on granad road were coming from! Looked like a very good turnout.

They are claiming over a thousand cars. Not sure if there were that many (at least not all there at once) but there were a few hundred easily.

have to take the intake runner off to get the injectors

and the timing belt idler/tensioner mounts off that, so you have to take the timing belt off

in short:

filter change = engine out

injector change = engine in pieces

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Hi. This is just my curiosity because iam sure the tuner figure something out...but either way i want to ask. The "problem" is that the Nistune ECU (Stagea FW and RB25DET NEO from Stagea) sees many times the speed than the speedo does(he says the speedo show 120 km/h - correct speed and the ECU shows like 510km/h ) I told him that this car/tranny getting speed from rear diff. If iam not mistaken the RB25DET NEO "need" to see tranny speed sensor? (my tranny has the plug for it). So couple of "question" If he connects/wire the speed sensor to the tranny...are the signals gonna intervene and if...what if he disconnects the rear diff one and the speedo stops working? Or the "new" sensor from the tranny "take over" and will not going need the one from diff? As i said i know he figure/get that done...iam just curious to know what are the solutions 🙂 
    • Your IACV is set to idle too low. You need to adjust it via the screw Duncan mentioned. From memory it should be 650rpm with the valve electrics unplugged. What is it trying to idle at with the IACV plugged in?
    • Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
×
×
  • Create New...