Jump to content
SAU Community

Recommended Posts

So ive got my new High-Flow from hypergear and have been advised by many of you guys on these forums to get the injectors and AFM before my tune otherwise ill just have to tune it twice. (Safe tune with standard Inj etc & then retune with new Inj etc)

I have been been reading through Trents (URAS) FAQ on the EMU and it seems as though I can adjust settings fairly easily.

I have all the usual mods and I am running a Greddy EMU, so my question is if I get the software for my EMU and fix the settings for a Z32 AFM can I also redo settings for the Injectors so that I can drive down to CRD for the final tune?

Also if I was planning of playing around with E85 would 750cc Nismos be sufficient??

I am not out to fully tune it myself but I want to save the installation cost of getting CRD to install the Inj's and AFM cause I can do it myself.

Any views would be greatly appreciated.

yes you can change the AFM and injector setting in EMU then drive to CRD for tuning

I would leave the fine tuning of lag times etc to them

as for changing AFM its just in the drop down box on the front page in vehicle settings and injectors are a simple before and after

no in the emanage car setup menu there is a tab called I/J from memory and the first area down the bottom will say 380cc for your before then in the next Box (the after ) you enter the size of your new injectors and the emanage will scale them for you,well good enough to get you to the tuners anyway

www.mohdparts.com

halfway down

you will have to download the full version then update to the latest

also if you havent installed the emanage yet

dont forget to do the jumpers (from memory only jumper no8 needs to be changed )

and you will more then likely need an adapter for inside (the ignition adapter)

Haines

Sorry mate I should have been clear with my original post. EMU is already installed. Was done in early 08 bt CRD, just after the software to have a play on the laptop.

joeyjoejoejunior....(What a mouthfull!) so 750's will be plenty with the "standard mods"? Im currently running 217rwkw before Highflow with standard AFM & Injectors aiming for around 250 odd with the Highflow but maybe a bit more with E85

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...