Jump to content
SAU Community

Recommended Posts

Gents,

Sat 13th December is the day. $100 buys you 8 hours of drift fun at the Eastern Creek skidpan and figure 8 wet track. We need 40 people to make this fly and the numbers look fine from the interest post.

What will you need? a roadworthy car, long sleeves and pants non-flammable. No Helmet (to be confirmed!)

What will you get? 1min flat out drift on the two circuits every 20-min. An instructor will be on hand to give advice and help out with control.

Starts 9am and finishes at 5pm. Food and drinks will be available at the creek.

For those of you who are only interested in the 1/2 day please PM me and don’t use this post. I will work something out with Dave once I have the numbers.

No deposit is needed as wet weather only makes the day more fun, but please, only post up if you are 100% confirmed, if we don’t get the numbers then Dave will not run this even again and we will loose out in the long run.

Any questions let me know.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/26149-drift-day-sat-13th-december-at-ec/
Share on other sites

  • Replies 188
  • Created
  • Last Reply

Top Posters In This Topic

All,

Bad news Dave just went to book the pans only to find out it was booked by someone yesterday. I will now change the date to the Sat 13th Dec.

Blitz,

Can you please change the Date in the post.




  • Similar Content

  • Latest Posts

    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
    • OK, if it idles at 1000+ with the AAC, its not an idle airflow problem. The cold start valve just gives extra air when the engine is cold, but you have enough air without it to idle at 1000. I think you are back to a fuel problem, sorry. Can you see the fuel pressure staying constant or does it drop as the revs drop to a stall?  
×
×
  • Create New...