Jump to content
SAU Community

Recommended Posts

R32 GTR SKYLINE, GUNMETAL GREY, BRIDE BUCKET SEATS, MOTOR NEEDS REBUILD OTHERWISE VERY STRAIGHT AND CLEAN CAR, STILL REGISTERED TILL AUGUST 2009 NSW REGO, THIS CAR HAD SOME WORK DONE TO THE MOTOR AND WAS TOLD BY THE PREVIOUS OWNER TOLD ME IT WAS AN 11 SECOND CAR AND WAS TOLD IT HAS BALL BEARING TURBOS AND TWIN PLATE CLUTCH, THIS CAR WAS VERY QUICK.

MOTOR DEFINITLY NEEDS REBUILD CAUSE THE RINGS ARE GONE, ALSO MOTOR WAS PRESSURISING AND PUSHING OUT THE DIPSTICK AND OIL. ALSO HAS LOW COMPRESSION IN ONE OF THE CYLIDERS.

EVERYTHING ELSE IS GOOD AND WORKING FINE IN THE CAR LIKE GEARBOX AND DIFF ETC...

ALSO FORGOT TO MENTION THE CAR HAS LITTLE BIT OF RUST ON TOP OF WINDSCREEN.(SEE PICS)

CALL 0416 899 511

NUMBER PLATE ( GTR 18R)

$9500

post-60633-1237522953_thumb.jpgpost-60633-1237522984_thumb.jpgpost-60633-1237523056_thumb.jpgpost-60633-1237523084_thumb.jpg[

attachment=212879:omars_gtr.jpg]post-60633-1237523197_thumb.jpgpost-17838-1139228954.jpgpost-60633-1237523422_thumb.jpgpost-60633-1237523528_thumb.jpg[a

ttachment=212885:Image018.jpg]post-60633-1237523688_thumb.jpgpost-60633-1237523752_thumb.jpg

post-60633-1237523024_thumb.jpg

post-60633-1237523165_thumb.jpg

post-60633-1237523300_thumb.jpg

post-60633-1237523583_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/261971-r32-gtr-skyline-cheap-9500-new-pics/
Share on other sites

is it just me or could some1 buy this and build the engine properly (forged pistons ect ect) and then end up with a cheap built 32gtr?

just thinking out loud, personally i wish i had the money to snap this up.

good luck with the sale mate

R32 GTR SKYLINE, GUNMETAL GREY, BRIDE BUCKET SEATS, MOTOR NEEDS REBUILD OTHERWISE VERY STRAIGHT AND CLEAN CAR, STILL REGISTERED TILL AUGUST 2009 NSW REGO, THIS CAR HAD SOME WORK DONE TO THE MOTOR AND WAS TOLD BY THE PREVIOUS OWNER TOLD ME IT WAS AN 11 SECOND CAR AND WAS TOLD IT HAS BALL BEARING TURBOS AND TWIN PLATE CLUTCH, THIS CAR WAS VERY QUICK.

MOTOR DEFINITLY NEEDS REBUILD CAUSE THE RINGS ARE GONE, ALSO MOTOR WAS PRESSURISING AND PUSHING OUT THE DIPSTICK AND OIL. ALSO HAS LOW COMPRESSION IN ONE OF THE CYLIDERS.

EVERYTHING ELSE IS GOOD AND WORKING FINE IN THE CAR LIKE GEARBOX AND DIFF ETC...

ALSO FORGOT TO MENTION THE CAR HAS LITTLE BIT OF RUST ON TOP OF WINDSCREEN.(SEE PICS)

CALL 0416 899 511

NUMBER PLATE ( GTR 18R)

$9500

post-60633-1237522953_thumb.jpgpost-60633-1237522984_thumb.jpgpost-60633-1237523056_thumb.jpgpost-60633-1237523084_thumb.jpg

[

attachment=212879:omars_gtr.jpg]post-60633-1237523197_thumb.jpgpost-60633-1237523422_thumb.jpgpost-60633-1237523528_thumb.jpg[

a

ttachment=212885:Image018.jpg]post-60633-1237523688_thumb.jpgpost-60633-1237523752_thumb.jpg

If you taken the BRIDE BUCKET SEATS out would the price still at $9500 or a bit cheaper?

step 1. go to bank, get $20000

step 2. go to this guys house and pick up car for $9500

step 3. stop by just jap and pick up R33 GTR N1 crate motor for $10000

step 4. swap engines and bits

step 5. sell bits of old rb26

step 6. give it a good thrashing

your a bit too early for me mate... im planning on doing this in the near future, but not right now. good luck with it.

Ive got a very tidy black Jeep Grand Cherokee Limited for a swapsy...V8, leather, electric everything etc. 10 months rego etc

would look great slammed on 22's

Edited by DiRTgarage
  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...