Jump to content
SAU Community

20inch Rims On My 33gts-t.

MacR33
 Share

Recommended Posts

MacR33 Contributor

MacR33

Posted
  • Author
Posted
You could make them fit by buying a lower sized wheel? Lol 20" is just TOO big in my opinion. Good luck fitting, I got no other suggestions.

NAwww they are sexy tho :down: haha. anyone else got suggestions?? what if i flared the guards and got spacers??

donut_kng Experienced

donut_kng

Posted
Posted

if its hitting on the side the offset isnt right and you can fix it with spacers (make sure you get longer studs put in if you go this way), but then it will probably sit out the guards too much and you wont be able to lower it.

if its hitting at the top the tyre profile is obviously too high, 245/35 is huge for the front, shoudl be fine on the back, 225/30 is the way to go on the front and if the offsets are right you should be able to deck it hard.

MacR33 Contributor

MacR33

Posted
  • Author
Posted
if its hitting on the side the offset isnt right and you can fix it with spacers (make sure you get longer studs put in if you go this way), but then it will probably sit out the guards too much and you wont be able to lower it.

if its hitting at the top the tyre profile is obviously too high, 245/35 is huge for the front, shoudl be fine on the back, 225/30 is the way to go on the front and if the offsets are right you should be able to deck it hard.

The steering arm is sitting 1/4 over the tyre already... they are gunna be sitting way outside my guards.. lol. Im not lowering it. so not sure... :down:

4drftn Experienced

4drftn

Posted
Posted

iv got 20's on mine with 225/35's on the front and lowered, if you can stretch a tire it will be alright, as for top of the strut elbow joint the clearance wouldnt be any more than a 3mm gap, but doesnt cause any problems. just make sure if its lowered the suspension is tight otherwise when the wheels are turned under hard cornering or similair the tire will hit... flaring or wide body fenders will fix the problem but as said above it is a bit of stuffing around.

4drftn Experienced

4drftn

Posted
Posted
your username and presumably rego is 4drftn and you have 20's?

DAMN you must have a lot of coin! :laugh:

lol, yeah i had a set of deep dish 17" volks when i first bought the car, chucked the 20's on to raise it off the ground so i could get out off the driveway... would like a set of nice dished racing rims though...

nisskid Grand Master

nisskid

Posted
Posted
lol, yeah i had a set of deep dish 17" volks when i first bought the car, chucked the 20's on to raise it off the ground so i could get out off the driveway... would like a set of nice dished racing rims though...

no offense, but thats about the most stupid thing ive heard all day.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Matt Z
      SAU NSW - Archies Flame Grille Meet & Cruise to Kurnell

      By Matt Z · Posted

      Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Ozdavroz
      WTAC 2025

      By Ozdavroz · Posted

      Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • bcozican
      WTAC 2025

      By bcozican · Posted

      i will be there 😁
    • patrickxdf12
      Squeaking clutch/throw out bearing

      By patrickxdf12 · Posted

      Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
×
×
  • Create New...