Jump to content
SAU Community

Power Steering Issue.

Ehgriez

By Ehgriez,
in Western Australia

 Share

Recommended Posts

Ehgriez Mentor

Ehgriez

Posted
Posted

Hey guys.

I've had the strangest issue recently. When I speed up to around 80km/hr I can feel the steering wheel shift to the left and then it stays on an angle until I slow back down where it straightens back up.

I have a feeling that it has something to do with the speed sensitivity of the power steering as it seems to happen at around the point you would expect the steering to be heavier.

Anyone got any ideas on what the issue might be? Only noticed it occurring on Friday.

Cheers,

Greg.

Link to comment
https://www.sau.com.au/forums/topic/262583-power-steering-issue/
Share on other sites
R DIRTY 3 Grand Master

R DIRTY 3

Posted
Posted

Are you talking about the position of the steering wheel?

If so, sounds to me like it might be a loose steering rack on the mounts. Could be caused by worn standard rubber bushes.

Happy to take a look if you need/want. :(

**RB2530** Proficient

**RB2530**

Posted
Posted

Yep this is Hicas playing up...

I have found that whenever I do a wheel alignment or anything where I turn the steering wheel from full lock to lock with the engine off, the Hicas computer goes into some sort of diagnostic mode.

The symptom of this is that the Hicas rack seems free to float or do what it wants. The first thing you notice is you have to correct for this with the steering wheel. Typical the wheel is 10deg of centre on straight road...

The way I fix this particular issue is to stop the car, turn off engine with wheels facing forward. Wait 10-20 secs and then start the car again. All is fine after that.

Now this 'may' be what is happening with your car. OR it could be a fault with Hicas..but definitely something to do with Hicas..

Ehgriez Mentor

Ehgriez

Posted
  • Author
Posted

It seems to be more like 30degrees off centre. It is also perfectly straight at low speed, I can FEEL it shift when i speed up.

R Dirty 3 It would be great if you could have a look sometime, I head up to Ellenbrook pretty often anyway.

Have a HICAS lock bar in my boot, should probably get around to installing it.

Cheers,

Greg.

bubba Grand Master

bubba

Posted
Posted
It seems to be more like 30degrees off centre. It is also perfectly straight at low speed, I can FEEL it shift when i speed up.

R Dirty 3 It would be great if you could have a look sometime, I head up to Ellenbrook pretty often anyway.

Have a HICAS lock bar in my boot, should probably get around to installing it.

Cheers,

Greg.

Put the lockbar in and then take it to Brad to be re-aligned, you won't regret it :P

2LV8ETR Mentor

2LV8ETR

Posted
Posted

Mine did this too.

My problem was the result of the HICAS ring location in the boss kit being out of alignment due to the adhesive coming unstuck.

The HICAS thought that the steering wheel was in a turned position and shot the rear wheels out. Twas funny crabwalking down the road at speed.............

Throw out the HICAS. Best move you could make.

Ehgriez Mentor

Ehgriez

Posted
  • Author
Posted

ok we ripped that shit out tonight, 3 hours or so of work.

Noone mentioned how f**ked up the bolts are that hold in the hicas actuator thingimy, a good hour of that 3 hours was me grunting and pulling at a huge breaker bar to get a 1/8th turn out of the damn thing-.-

Ah well, got it off in the end. Can anyone clarify which of the boxes under my parcel tray is the hicas one? Is it the one stamped with NISSAN on the passenger side, or the other one on the drivers side?

havoc34 Enthusiast

havoc34

Posted
Posted

Hi am new in here. Am driving a R34GTT. Well I seem to have this same problem but mine is the steering wheel to drive stairght I need the steering wheel at abt 5 degrees to the right. Even after alignment done they had to manaully drive and adjust the toe to the fronts for the steering wheel to drive staright but after driving a while it well go back to the same?? Done 3 alignments from differeent places the last was at Malaga Suspensions the got the steering wheel centre but still can when ard 100km/h it starts to pull to the right. Can it be what you guys are talking abt tht my HICAS is also f**ked? And how to confirm? Hope you guys can help me out?? Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Looking for someone with a R34 front bar

      By GTSBoy · Posted

      That looks good, but I think you're going to need much beefier side skirts now.
    • GTSBoy
      Most women will agree that parking is the most taxing part of driving

      By GTSBoy · Posted

      They are daft and there's a reason it never caught on. Steering feel? We don't need no stinking steering feel!
    • GTSBoy
      new 1.5 LSD issues/concerns

      By GTSBoy · Posted

      I gotta pull you up on this. It's driving me crazy. A shutter is something that closes, like over a window or in a cmera. The word you want is shudder. That LSD is clearly f**ked. Take it to a diff shop and get it disassembled and examined by an expert. YOu might have plates welded together or something equally crazy.
    • GTSBoy
      M35 Brake caliper replacement

      By GTSBoy · Posted

      Define "starting to fail". Wy not just rebuild them?
    • GTSBoy
      S1 rb25/s14 starting problem

      By GTSBoy · Posted

      Check the Nistune doco. There are a few assumptions being made here that might not be valid. I will list the things that occur to me: Base map. Base map for what? Base map for Z32? Then the cranking pulse width is probably wrong for an RB25. The extra 500cc of capacity might well be enough to prevent it from catching. Base map for RB25? I don't think you can load one of those into a Z32. You have to just make the settings correct for an RB25 in the Z32 base map. That is either K or the TIM to get the pulsewidth right. Loom. You bought a loom for an RB. And you plugged it into a Z32 ECU. Did you make sure that any iwre differences were swapped. From memory, there's at least a couple. And as per the others, I would suggest making sure that the fuel pressure is correct while cranking and that the injectors are actually flowing as expected. They really must come out and go on the bench, unless you do find that you have messed up as per above points. I would also suggest watching in Nistune to make sure that everything is reading correctly. That the correct binary flags are raised at the right time (like the crank signal), that there's no stupid values in K or TIM. That you have not got mismatched firmware for the ECU and/or a wrong image loaded.
×
×
  • Create New...