Jump to content
SAU Community

Recommended Posts

hey guys just helping a friend out whos got a bunch of stuff thats been left over from his 3L build.

just a note all the following is off a Rb25 NEO form a 2000 model R34 GTT

Mirror Finish Plazmaman Plenum = $850 FIRM

done around 15,000km still in NEW CONDITION STATE

direct bolt onto R34s and gets rid of all the ugly wires and looks hektic lol

throttle20body208.jpg

72mm Plazmaman Throttle body to suit Plazmaman Plenum = $380 firm

more air flow = more kws =D

throttle20body203.jpg

SARD 800CC Injecors. $800 - ONO

sorry no pics yet =[

6boost Steampipe Manifold Suit T3 - $800 ONO

no pics yet guys =[

Garrett GT3540 .86 Rear - $1500 ONO

made 350rwkw on my 3L setup @ 20psi

done around ~15,000kms

ggt3540.jpg

Splitfire Coilpack - $550 ONO

sfdis001lv4.jpg

RB25 NEO HEAD - $1500 ONO

complete with wiring loom and has done around 70,000kms serviced every 5,000kms.

Blown RB25 NEO Bottom End - make an offer

not much to say about this one lol.

well guys thats it. any questions feel free to ask or call me on 0421691338. working most of the time so leave a message if i dont pick up.

cheers :blush:

Edited by VB-

Hey bud just wondering why youre selling everything?

Because you blew the engine?! lol

Interested in the Manifold, in melb too.

Im assuming high mount? Also is it an external gate manifold? What gate did you use with it?

You used with manifold with the turbo with no dramas?

Cheers.

Hey bud just wondering why youre selling everything?

Because you blew the engine?! lol

Ye, sounds like anDru has minced a motor doesn't it? :D

Either way

"hey guys just helping a friend out whos got a bunch of stuff thats been left over from his 3L build."

Closed. Get your 'friend' to post up... but then if its anDru, he might have a few problems doing that.

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Hi. This is just my curiosity because iam sure the tuner figure something out...but either way i want to ask. The "problem" is that the Nistune ECU (Stagea FW and RB25DET NEO from Stagea) sees many times the speed than the speedo does(he says the speedo show 120 km/h - correct speed and the ECU shows like 510km/h ) I told him that this car/tranny getting speed from rear diff. If iam not mistaken the RB25DET NEO "need" to see tranny speed sensor? (my tranny has the plug for it). So couple of "question" If he connects/wire the speed sensor to the tranny...are the signals gonna intervene and if...what if he disconnects the rear diff one and the speedo stops working? Or the "new" sensor from the tranny "take over" and will not going need the one from diff? As i said i know he figure/get that done...iam just curious to know what are the solutions 🙂 
    • Your IACV is set to idle too low. You need to adjust it via the screw Duncan mentioned. From memory it should be 650rpm with the valve electrics unplugged. What is it trying to idle at with the IACV plugged in?
    • Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
×
×
  • Create New...