Jump to content
SAU Community

Recommended Posts

  • Replies 48
  • Created
  • Last Reply

Top Posters In This Topic

Have you already sourced a Top Secret front bar? If so, where from?

I was ordering one from the spoiler shop here in perth, turns out they cant get them at the moment and I'd probably be waiting 4-6 months! Need to find someone that has it in Perth, im pretty decided on this kit and dont want to have to change my mind again, lmao

post-4164-1238558931_thumb.jpg

this after installing them, later on i recessed them in a bit further, tinted them and put mesh over the holes.

its a 400r front bar, but i didnt want the ghey round indicators in the uprights, they look terrible

post-4164-1238558931_thumb.jpg

this after installing them, later on i recessed them in a bit further, tinted them and put mesh over the holes.

its a 400r front bar, but i didnt want the ghey round indicators in the uprights, they look terrible

Hey mate,

Clean ride buddy...that's something different alright...but not really my thing too...but I agree with you, those round big fat lights in the middle (unless they're original Nissan GTR ones), look gay as hell...

What I may do is as per my first pictures...mount smaller indicators at the front...don't know yet...decisions, decisions...

Fellas, you can get the Top Secret bar online on EBAY...I've looked everywhere else and cannot find it...just type in R33 Top Secret and you will find it...go for it, a few good specials now... a mate of mine purchased a full kit from the only ebayer that sells them and said they fit like a dream!

will it fit GTST ?

Sure will mate, but you will have to fold the sides into a bit and refibreglass it to fit...as the GTR guards are a bit more flared as you know...but sure...it will work...

I used S15 Silvia sidewinkers and they fitted like a charm, the only problem now is that my flashers blink very fast because of the lower wattage of the new winkers. :(

Heres a couple more pics, i bought two 4 LED clusters they are small as but light up very bright :D they were like 30 bucks for the pair from autobarn but well worth the buy (much better then using trailer lights imo) i just cable tied the rear clips on the back of the indicators through the mesh that i had on my front bar.. works a treat and my dad helped me with some tidy cabling / heatstrink

post-34834-1239239738_thumb.jpg

post-34834-1239239813_thumb.jpg

post-34834-1239239838_thumb.jpg

cheers

Oh and i should mention that when buying LED indicators the frequency is faster or something, so flashes fast a resistor can fix it I'm just lazy, i got defected for having a tiny bit of metal on my old steering wheel and they checked all my lights etc and didn't say anything about them flashing too fast or anything.. so should be fine unless you get annoyed by the little arrow on your dash --> going fast :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Dear folks My family members have 4 different cars : Triton 2015 and Corolla 2011 and Mazda3 2012 and Hyundai Elantra 2014 Looking to buy engine oil funnel spill free What I found are are below  https://www.amazon.com/gp/aw/d/B0BBTTJNKX?ref=ppx_pt2_mob_b_prod_image&th=1 https://www.ebay.com.au/itm/145553221359?srsltid=AfmBOoqYBU6Ptw0LU_bAp_k67U3qkF97HHvePkA7iHZw8vUmiwoIRaRr https://www.amazon.com/gp/product/B09X23TCS5?th=1 Is there a funnel with attachment that fits most cars ? Don't mind to spend for a decent quality  Thx  
    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
×
×
  • Create New...