Jump to content
SAU Community

Recommended Posts

Well some of you might know me and some of the controversy my car has caused(your numbers are fake aussie dyno's rule etc etc) its an 98 ecr33 40th anny hada built rb25 on it tomei rods cp pistons 35r port n polish stock cams greddy intake mani haltech platinum ems , well that setup dyno'd 607rwhp at 30 psi on pump gas and meth injection on a mustang dyno, some of you may know about them most of you dont go figure, well i took it apart found a nice rb26 from an r33 and started to build it up

here are the specs

arias pistons

tomei rods (from the 25)

kelford 272 10mm lift cams

Haltech Platinum sport 2000

bullseye power S368 (should get me to 1k high boost and race gas)

greddy cam gears

6 boost exhaust manifold

44 tial(high boost aplication)

nismo oil pump

ferrea valve springs n retainers

port n polish

calico coated acl bearings

match ported exhaust intake itb and intake manifold(rb26 comes really badly matched

arp head and main bolts

cometic head gasket

exedy triple carbon

NX single nozzle kit 50-150hp

and thats about it hoping to make 1k on race eventually after allot of fine tuning(hopefully no giggle gas) but should get to 900 prety easily (crank hp)

oh yea built and tuned by me rawr

Link to comment
https://www.sau.com.au/forums/topic/263262-rb26-build-900crank-hp/
Share on other sites

And the point of this post is ???

plenty of other posts on this forum with no meaning or point 1 more wouldnt hurt wouldnt ya say? could be worse i could of made another gt35r or t04z threads woohooooooo

nah just stating im on another build thats all nothing fancy

bullseye power S368 (should get me to 1k high boost and race gas)

Awesome stuff :O By "1k high boost and race gas" do you mean 1000hp? I am pretty sure they are pushing it to crack 800hp compressor alone, unless you mean including nitrous oxide?

Awesome stuff :D By "1k high boost and race gas" do you mean 1000hp? I am pretty sure they are pushing it to crack 800hp compressor alone, unless you mean including nitrous oxide?

dont think the bw is goin to crack anywhere really, this same turbo ran 750 fwhp on actualy prety low boost levels 36 psi on a 1.8 liter vw golf but with a .70 ar t3 housing im puting a 1.0 divided t4 and at 42 pounds with a much bigger engine and bigger cams should make a prety nice numbers should easily see 900 crank and get to 1000 btw these are normal dyno's not rigoli dyno's that read like 200-300hp less lol, these extended tip turbos are making a real dent into the import racing world every 1 is using them now over on the other side of the pond, thiers a gtr in dominican republic with a stock internal rb26 with greddy stage 1 cams and a s370-72 dyno'd 640 awhp on low boost and really conservative tune bone stock engine at 30 pounds , thiers also a z32 with an rb26 with a similar but smaller turbo that runs 10.4's on e85 with mt et super streets at 25 psi with an s366 i think he dyno'd 650 rwhp we'll see what i do though

Edited by ReganGTS25T

Awesome it would be good to see it if its possible to go that high. The S368s aren't stupidly laggy so if you can do that then its a damn good case against using things like a GT42R.

I'm used to Dynapack dynos myself - remember I backed you in another thread regarding that topic :D I know the Honda guys have got up over 700whp on them but those engines breathe crazily, and with a FWD (hardly any trans losses) thats around 800hp @ crank and probably near the limit... I always thought the S372 is more the 900-1000hp unit.

Awesome it would be good to see it if its possible to go that high. The S368s aren't stupidly laggy so if you can do that then its a damn good case against using things like a GT42R.

I'm used to Dynapack dynos myself - remember I backed you in another thread regarding that topic :D I know the Honda guys have got up over 700whp on them but those engines breathe crazily, and with a FWD (hardly any trans losses) thats around 800hp @ crank and probably near the limit... I always thought the S372 is more the 900-1000hp unit.

well the md's suposedly read 10% less then dyno packs also they factor in wind coeficient factors for every car from 1973 to 2008 its nice, yea hondas are nice but displacement is nice also yea i didnt want to go with a 42r or an equivilant of it in borg warner (ill never buy another garret turbo) its my daily driver want to see full boost inside of 4krpms 4900 will do :D lol but yea it has the new race cover n stuff bullseye is also coming out with a new billet extended tip wheel which i can just buy later and test it out, you know borg warner has titanium billet compresor wheels you can make carrot puree and not even dull the compresor wheel :D

Thats useful to know :D You best keep away from the garage when you have drinks, if you were anything like us the idea of twisting the compressor housing and popping the intercooler hose off for making some smoothies is bound to come up haha

plenty of other posts on this forum with no meaning or point 1 more wouldnt hurt wouldnt ya say? could be worse i could of made another gt35r or t04z threads woohooooooo

nah just stating im on another build thats all nothing fancy

Very well, I wish you all the very best for your build and I hope you can crack the magical 1000hp. This figure is normally reserved for highly strung RB26's or 2JZ's so best of luck, I hope to see you run 9's.

  • 4 weeks later...
dont think the bw is goin to crack anywhere really, this same turbo ran 750 fwhp on actualy prety low boost levels 36 psi on a 1.8 liter vw golf but with a .70 ar t3 housing im puting a 1.0 divided t4 and at 42 pounds with a much bigger engine and bigger cams should make a prety nice numbers should easily see 900 crank and get to 1000 btw these are normal dyno's not rigoli dyno's that read like 200-300hp less lol, these extended tip turbos are making a real dent into the import racing world every 1 is using them now over on the other side of the pond, thiers a gtr in dominican republic with a stock internal rb26 with greddy stage 1 cams and a s370-72 dyno'd 640 awhp on low boost and really conservative tune bone stock engine at 30 pounds , thiers also a z32 with an rb26 with a similar but smaller turbo that runs 10.4's on e85 with mt et super streets at 25 psi with an s366 i think he dyno'd 650 rwhp we'll see what i do though

Regan...you're right about the 640 four wheel hp stock internal......and now we are going for even better numbers with everything forged. 10.43 but looking to enter into 9's

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
×
×
  • Create New...