Jump to content
SAU Community

Recommended Posts

Hey guys Im stripping an RB26 GTR complete Engine. I bought the head for RB30 project but did not go ahead. And the Block is from an old GTR engine that I had I bought pistons and rods, then realised the block needs boring.

Tell me what you need and PM me your offers....

Plenum & Throttle Bodies

Injectors

Fuel Rail (injector feed)

Two Turbos In ecxellent condition No leaks No shaft play never been boosted

Dump pipes

Turbo side Manifolds and Heat shield

Cam Gears

Head Complete (Cams, springs, valvs, shims, ect....)

R33 GTR Pistons Excellent condition.

R33 GTR Rods Excellent condition

R32 GTR Block needs boring as it has marks on the cylinders. So u would need bigger pistons.

PM me what you need and your offer please.

Link to comment
https://www.sau.com.au/forums/topic/264679-stripping-gtr-rb26-engine/
Share on other sites

  • Replies 41
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

OK as Requested here they are:

ALL PARTS ARE LOCATED IN SYDNEY

Plenum & Throttle Bodies. $700 ono

Injectors. $400 ono

Fuel Rail (injector feed). $80

Two Turbos In ecxellent condition No leaks No shaft play never been boosted with Dump pipes. $700 ono

Turbo side Manifolds and Heat shield. $400 ono

Head Complete (Cams, springs, valvs, shims, cam gears ect....) No covers. $1000 ono

R33 GTR 6 Pistons Excellent condition. $300 ono

R33 GTR 6 Con Rods Excellent condition. $200 ono

R32 GTR Crank Shaft. $250 ono

R32 GTR Block needs boring as it has marks on the cylinders. So u would need bigger pistons. $500 ono

If you buy more than one part discount can be applied.

For sale is another 5 Piece complete set of Rocker Covers it includes:

2 Cam Covers

Timing Cover

Cam gears Plate (goes behind the Cam gears)

Ornament Badge (goes between the Cam Covers, Covers the coil pack)

$400

Located in Sydney

post-57341-1239233566_thumb.jpg

Head Is SOLD pending Payment...

The following is still 4 sale I've reduced the prices:

Plenum & Throttle Bodies. $500

Injectors. $350

Fuel Rail (injector feed). $50

R32 GTR Crank Shaft. $200

R32 GTR Block needs boring as it has marks on the cylinders. So u would need bigger pistons. $350

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
×
×
  • Create New...