Jump to content
SAU Community

Recommended Posts

All items available Shipped (at buyer expense) or Pick Up from Braeside, Melbourne Australia , only after payment cleared, contact through this website by PM to discuss item, payment and pick or shipping/delivery ( at your expense).

1. OS Gliken Clutch triple plate suit R34 6Speed Excellent Condition $1200

+ Flywheel (like new)

post-50630-1239770467_thumb.jpgpost-50630-1239770516_thumb.jpg

2. R33 GTR RB 26 std Injector + rail Good Condition $250

post-50630-1239770778_thumb.jpg

3. R33 GTR Dash Surround - no speed cluster Good Condition $300

post-50630-1239771024_thumb.jpg

4. GTR R33 Grill Insert $250

post-50630-1239771147_thumb.jpg

5. Kenwood 10 Stacker CD $100

post-50630-1239771275_thumb.jpgpost-50630-1239775875_thumb.jpg

6. GTR R33 brake Master Cylinder $100

post-50630-1239771397_thumb.jpg

7. R33 GTR Vspec Front brake Ducts $150

post-50630-1239771570_thumb.jpg

8. Rear Parcel Tray R33 GTR $80

post-50630-1239771773_thumb.jpg

9. Radiator GTR R33 (2 of Available, each@-sell sep.) $120

post-50630-1239772022_thumb.jpg

10.R34 GTR 6 Speed Transmission - from 2002 V-Spec2 18000klm Good Con $3000

with Transfer case

post-50630-1239772247_thumb.jpg

11. GTR - Vspec 33 Diff Center Good Condition $550

post-50630-1239772470_thumb.jpg

Edited by JFKGTR
Link to comment
https://www.sau.com.au/forums/topic/265560-gtr-parts-and-accessories-for-sale/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...