Jump to content
SAU Community

Recommended Posts

my mate has smashed his 32 GTR few weeks ago, passenger side banana'd

FRONT LIP AND REAR INTERIOR TRIMS ARE NOT!! AVAILABLE!

front bar only, no lip. $150 (needs a 10cm section to be plastic welded, has n1 slots)

front guards $600/pair

front reo - $150

rear reo - $150

bonnet $600

front lights $300

front grille $200

front brakes (incl. DBA slotted rotors)/rear brakes incl all 4 hubs $800

rear cut with quarter panels $1000

seats front / rear $700

drivers door with glass $250

centre console $50

stereo/shiter surround $75

door trims $100/pair

carpet $50

cluster surround with switches $100

RB26DETT with fresh recod head ($2500), just last week!! loom and ecu $4500

gearbox $500

bootlid and wing $300

complete body loom not incl dash, but all the way to rear incl fuel tank etc etc $400

mines ECU $250

IF THERE IS ANYTHING U NEED PLEASE PM ME AND ILL SEE IF WE HAVE IT AND ITS INTACT!!!

pm me with ur email address and ill send pictures!! i have pics of most of the stuff.

Link to comment
https://www.sau.com.au/forums/topic/265635-r32-gtr-most-parts-available/
Share on other sites

front bar only, no lip. $150 (needs a 10cm section to be plastic welded, has n1 slots)

seats front / rear $700

What colour is the bar?

Would you split the seats? need fronts, already have rears.

Can pick up this week.

Paul

0403433579

no aftermarket parts sorry, possibly a cat back exhaust, gota check the condition tho if its bent/damaged, honestly cant remember

did you find out about exhaust?

im after a centre part only depending on the style of exhaust it is

can you post pics

cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
×
×
  • Create New...