Jump to content
SAU Community

Suspension Soft & Bouncy After Motor Change

boostdef
 Share

Recommended Posts

boostdef Enthusiast

boostdef

Posted
Posted

Hi,

Can anyone tell me whats going on? I have just changed the motor in an R33 gtst which has khoni adjustables at the front, and the from suspension is extremely soft and bounces like a boat in waves as im driving along.

I did not touch the suspension at all, just a simple jack the car up, change the motor and put it back down?? wtf?

Any help would be greatly appreciated :blink:

nisskid Grand Master

nisskid

Posted
Posted

sway bars still connected properly? dont think u need to take them off to change the engine, but it does go near to the sump so its possible. also did u have a strut brace on before? not usually a noticeable "handling" difference, mostly a mid-corner grip thing.

also was it a straight engine swap? u didnt put a heavier engine in did u?

boostdef Enthusiast

boostdef

Posted
  • Author
Posted
sway bars still connected properly? dont think u need to take them off to change the engine, but it does go near to the sump so its possible. also did u have a strut brace on before? not usually a noticeable "handling" difference, mostly a mid-corner grip thing.

also was it a straight engine swap? u didnt put a heavier engine in did u?

Straight engine swap by replacing a S1 motor with a S2 motor.I dont recall at all undoing any sway bars. Was pretty much engine mounts, bellhousing bolts and the little things here and there and that was it.The shocks i think are khoni adjustables with a bolt at the top, and i think a something to adjust underneath.Its just like they are now ultra soft and i go over 1 bump and the front goes up and down constantly for about 10 seconds. Plus, it is bottoming out a lot more obviously due to the softness :(Can I simply adjust them at all? Is it the top bolt i adjust or underneath? (Sorry new to this)

boostdef Enthusiast

boostdef

Posted
  • Author
Posted
Didnt drop the engine in to hard and bust the seals in the shocks did you?

Naa it all seemed smooth as! Dropped it in extremely carefully. But I suppose thats a possibility I may have done something.Another thing I forgot to mention is they are Coilover types i think. Ones with the adjuster at the bottom of the spring and the bolt at the top. Can it simply be a case of stiffening the spring? (Not that it explains what the go is though :P)

nisskid Grand Master

nisskid

Posted
Posted
Straight engine swap by replacing a S1 motor with a S2 motor.I dont recall at all undoing any sway bars. Was pretty much engine mounts, bellhousing bolts and the little things here and there and that was it.The shocks i think are khoni adjustables with a bolt at the top, and i think a something to adjust underneath.Its just like they are now ultra soft and i go over 1 bump and the front goes up and down constantly for about 10 seconds. Plus, it is bottoming out a lot more obviously due to the softness :(Can I simply adjust them at all? Is it the top bolt i adjust or underneath? (Sorry new to this)

sounds like ur shocks are buggered for some reason, are they on full hard adjustment wise?

boostdef Enthusiast

boostdef

Posted
  • Author
Posted
sounds like ur shocks are buggered for some reason, are they on full hard adjustment wise?

The bottom coil adjustment is about half/half, and the top bolt is just on the thread (ie the shaft of the shocks are just above the top of the bolt.

Would having the wheels in the air for an extended time do this? Because thats the only thing I can think of really.

petern Enthusiast

petern

Posted
Posted (edited)

i think you just answered your own question in that last sentence......

having the the wheels in the air for an extended period would put pressure on the shocks - weight of the wheels and brakes.

I know when I disconnect the shocks on the rear on my 1600, i can push down on the back and bounces a fair bit.

I would say shocks are stuffed!

Edited by petern
nisskid Grand Master

nisskid

Posted
Posted

wheels in the air shouldnt bust ur shocks, as they are still in the static position, but will put a bit of pressure on the travel stops if it is infact the shocks which are suspending the wheel, often its the arms/rods or half shaft suspending the wheels up, and the shocks arent.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • joshuaho96
      Cas issue

      By joshuaho96 · Posted

      Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • joshuaho96
      Jacks that fit under GTR lips that can reach the subframe?

      By joshuaho96 · Posted

      On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Nice....looking forward to that update
×
×
  • Create New...