Jump to content
SAU Community

Recommended Posts

befor u go and pay $500-$600 for coilpacks, get some heat temp proof silicone and fill in the gaps on your coilpacks so it cant earth out on head instead of on plug. Search coilpack budget mods, you might find pictures.

Link to comment
https://www.sau.com.au/forums/topic/266127-dodgy-coilpacks/#findComment-4543001
Share on other sites

Hey everyone!!

My brothers R34Gt-t is misfiring when ever you put the foot down a bit. Its fine when hes driving soft, but misfires bad when he tries to go hard. We've already changed the spark plugs and think now that it may be the coilpacks???

Any ideas???

(i did search but didn't find much...)

Thanks

Hi MATthere is lot`s on this may be you didn`t have much Searchluck it is hard some time`s :thumbsup: ,better luck next time,cheer`s chuckie .
Link to comment
https://www.sau.com.au/forums/topic/266127-dodgy-coilpacks/#findComment-4543654
Share on other sites

What gap are the new plugs he's using? and what boost is being run?

The issue sounds like coil packs (very common at higher boost levels) but the problem often can be reduced or eliminated by using plugs with a smaller 0.8mm gap (or less depending on boost) as opposed to the std 1.1mm gap.

This worked for me and the insulation of the coil packs didn't, I still have a slight miss and are currently waiting for JJR coils to be back in stock for the R33 S2.

Also Splitfires are great but they are $600+, Super Sparks can be had for $500, JJR have coil packs for $400 (1yr warranty) that do the same job and there are some Yellow Jackets just come on the market for $350 a set (6 month warranty). For my money I'm going for the JJRs - same warranty and result as Splitfires.

Link to comment
https://www.sau.com.au/forums/topic/266127-dodgy-coilpacks/#findComment-4553483
Share on other sites

does it hesitate coming onto boost? i had a similar issue, also had a dodgy idle, turned out to just be a vac leak. pulled out my coils and they looked brand new!! so just be sure to check everything before spending a few hundred on coils :)

Link to comment
https://www.sau.com.au/forums/topic/266127-dodgy-coilpacks/#findComment-4554183
Share on other sites

  • 2 weeks later...
What gap are the new plugs he's using? and what boost is being run?

The issue sounds like coil packs (very common at higher boost levels) but the problem often can be reduced or eliminated by using plugs with a smaller 0.8mm gap (or less depending on boost) as opposed to the std 1.1mm gap.

This worked for me and the insulation of the coil packs didn't, I still have a slight miss and are currently waiting for JJR coils to be back in stock for the R33 S2.

Also Splitfires are great but they are $600+, Super Sparks can be had for $500, JJR have coil packs for $400 (1yr warranty) that do the same job and there are some Yellow Jackets just come on the market for $350 a set (6 month warranty). For my money I'm going for the JJRs - same warranty and result as Splitfires.

Ive had a set of yellow jackets in my GTST for around 3 months now and they have never missed a beat. They actually come with a 12 month warranty too. Theres a group buy for them here on SAU and they are only $320. So cheaper than JJR, same results as Splitfire and same waranty.

Link to comment
https://www.sau.com.au/forums/topic/266127-dodgy-coilpacks/#findComment-4578373
Share on other sites

Try coating the coils as already mentioned and see how that works.

Splitfires aren't worth the money unless you aren't very mechanically inclined and/or you want a COP setup like stock. I am in the process of swapping my old coils since the epoxy didn't help in the high rpms. I picked up a set of 8 Chevy Corvette LS2 coils for $125USD and mounted them along the firewall with separate spark plug wires. They should blast the splitfires away and provide adequate spark for whatever I throw at them. Plus they have built in ignitors so I can get rid of my RB25 Series 1 ignitor/power transistor unit (PTU) and wire them directly from the ECU.

Link to comment
https://www.sau.com.au/forums/topic/266127-dodgy-coilpacks/#findComment-4578870
Share on other sites

Only problem i'v ever had with coils is when one died. Not sure any of the aftermarket ones can offer a much if any greater spark unless you introduce leads in to the equation like above...

before anything, like said before, clean out around the spark plug hole and clean the sleeves then spray it all with silicon spray and i can't see why unless a jacket is damaged you would have problems given that there is not a fault in the coil or wiring itself...

Link to comment
https://www.sau.com.au/forums/topic/266127-dodgy-coilpacks/#findComment-4579042
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Are you suggesting that the kit did a cheap and nasty job of just jamming the wheel in between other things and caused the misalignment? I mean, we normally do this with an integrated crank trigger wheel, not something bodged on. It's not 1995 any more.
    • I mean, given the number of BMWs you own their tolerance for improper torque is rather low. The number of torque + angle spec bolts and non-reusable bolts in one is nuts.
    • Atmospheric vent requires something that doesn't use a MAF for load. You would need a standalone ECU for that.
    • Hey all,   I’ve got an RB25 with a trigger kit that includes a crank wheel, and I’ve hit a wall trying to sort a timing belt tracking issue. The belt either rides right on the edge of the cam/crank pulleys or walks slightly forward once the engine starts. It tracks okay-ish for a moment, then creeps right to the edge—and honestly, it’s stressing me out.   I’ve spent hours removing and reinstalling the belt, double-checking everything:   Tensioner setup is good, checked multiple times Idler pulley and washers are all in the correct places Followed the RB25 timing procedure step-by-step     The only thing I changed was the rear crank washer—I swapped the OEM one for a Neato version, and it made things worse. The belt now sits even more forward than before. I’m beginning to think the crank trigger wheel itself (from the trigger kit) is the issue—poor design or slightly off dimensions.   What’s strange is that with the previous belt setup, it actually ran fine for a couple of years—around 4,000 to 5,000 miles, even with hard driving and high RPMs. But even then, the belt was always riding right on the edge, and I know that’s not ideal or safe long term.   At this point, I’m debating whether to:   Machine a few mm off the crank trigger wheel to bring it back in line, or Replace it entirely with a better-designed unit     Only thing is, I already have the Cherry Hall sensors, bracket, etc.—I just want to replace the wheel only, not the entire kit. Anyone know a brand or supplier that sells just the crank trigger wheel on its own?   Would really appreciate any feedback—especially from anyone who’s run into this exact issue and found a reliable fix.   Thanks in advance.
    • Hi...a little refresh. Is Nistune gonna be enough to run BoV? Or do i need some proper ECU? 
×
×
  • Create New...