Jump to content
SAU Community

Recommended Posts

Hi all

Does anyone know how to get all 4 rear lights lit up when braking?

I heard it's possible, however the brake light bulbs are easily blown if not done correctly, especially if the parking lights are on.

Is there a guide on how to do this properly?

Thanks

getting my dad to do this for me as he loves these kinda things.

from what i know what you will need is 2 double filament globes (same as you normal brake light but a size smaller so it fists the hole) and an inline fuse and globe holder.

locate which wire is the brake line wire splice into it it and run the wires to the right fittings int he new globe holder thing and presto.

its easy to do and kinda fiddley thats why my dads doing it for me lol but ye if no one has done this by next sunday ill have mine done by then and will put up a detailed instruction.

checked mine last night and all four tails brighten up when i brake, plus the small light top of boot lights up.

is that a standard thing on gtt? or is it gtt 4 door or has mine been modified i wonder??? I know i didnt do it... Pic below any help???

21042009126.jpg

Edited by STYLN

I think all 4 door has 4 lighting up cause that's the first thing I notice when I see a 4 door. Haven't seen any 2 door with 4 lighting up so far. Loved to do it to mine.. I thought it was just splicing the smaller light wire and join it to the main brake wire. I mean the ground wire of those 2.

Edited by ducki
  • 5 months later...

All four stay lit as in when you hit the brakes?

It'd be interesting to see if there are any noticable changes to the wiring.

Wouldn't happen to have time to take some pics would you? :)

as in the two smaller ones stay lit.. but don't go bright when i brake like the big ones..

i only noticed this when i replaced with just jap LED ones.. but am unsure if they were always like it.. i'm sure i could take a pic of the wires

Oh I think what you're talking about is the normal setup.

Both the outer and inner circles are lit when you have your lights on.. but when you hit the brakes, only the outer ones will go brighter.

I'm hoping to wire it so that even when I don't have the parkers on and I hit the brakes, all four will light up.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...