Jump to content
SAU Community

Recommended Posts

  • Replies 492
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

I wouldn't worry about it too much unless you're into it and that's specifically what you want to play. It takes mountains of time and obviously a correct technique, but it is doable. I can't get into the whole speed guitar thing anymore, lost interest and speed many years ago.

I wouldn't worry about it too much unless you're into it and that's specifically what you want to play. It takes mountains of time and obviously a correct technique, but it is doable. I can't get into the whole speed guitar thing anymore, lost interest and speed many years ago.

i learnt on a 35 year old masaru kohno japanese/spanish acoustic....

picking was a no no

fingerpicking = uber

i ended up playing my electrics like the spanish, without a pick. my fingers paid the price... i can simultaneously play bass and lead on a single guitar but double picking and hammeron hammer off is still beyond me

-D

Never too late to learn Ben. Flat (modern guitar) fretboard + low action = easy speed.

Maybe u can give me some tips steve. where are ya ? pm me ya details

i have an 86 fender telecaster heavy metal edition. only problem is the floating trem is cactus so imma replace it with an EVH transtrem. i never learnt how to use a tremolo bar, so probably the fixed bridge gibson would be best for me but i'd like yr opinion.

i got an EH Big Muff Pi, sovtek version, (late sovtek so its pretty much accurate), a marshall JMP 1 preamp and a fender frontman 212R

and i got a c-port DSP24 with 8 channel real time multichannel recording @ 24 bit /192 khz

-D

wtf. this has got to be one of the most filthy disgusting tunes. I f'n love it. played it 23 times loud.

Cant wait to mix it

http://www.youtube.com/watch?v=aRP9vDFZrj8...feature=related

dubstep is cool!

as a dubstep producer you could probably adapt so many different styles of sounds - techno, prog, and real grimey stuff like that above^

i reckon its a pretty big movement of a genre and will always have a good following - like drum & bass. Rather than like some genres that die in the arse i.e breaks...

Unless, it becomes commercialised and overdone like breaks did, then things can head downhill!

on another note; Anyone heading to BDO 2010???

'sold out' already. Hard to believe. I think its the usual promoter stunt so people to throw themselves at a second round release of tickets

I'm pretty keen to go, but not a ticket holder yet...

VERY keen to watch a set from this guy.

Sasha hasn't played in Adelaide for YEARS! He's playing all BDO's. Although I'd just hope they give him the closing set, and for at least 2hours - pretty pointless giving a progressive DJ (and the world's biggest) anything less!

Yeah I just missed out on the last bdo tickets. one of my mates got one of the last few tickets. Went real quick

I like listening to some real heavy metal music too. Love the drumming etc.

Luciano. you get that name from the producer ?

^ who, this dude: http://www.discogs.com/artist/Luciano -great techno/minimal DJ he is. Havent heard much of his production work

but nah, thats actually my real name on the birth certificate... named after my grandfather! i just go by Luke Luciano <insertsurnamehere> for ID's, accounts etc

  • 2 weeks later...

Pretty awesome Vinnie! thats one very technologically advanced piece of kit. i love the whole concept of digital - cdjs, serato, final skratch, midi controllers etc.

But, some of the features - who the hell is gonna use them in a live set! I think a lot of its there for the wow factor.

yee they look pretty good bit outta my price range...lookin at getting 2x cdj1000 mk3's and a djm800 if i can get the cash if not looks like i'll be getting cdj400's and a djm 400

haha Damo, this shit aint cheap hey. i actually expected them to be over 2.5k each.

1000's are still pretty pricey, unless you find some second hand for a good deal. But seeing as every trainspotting clubber wants to get their hands on a pair, good deals disappear quickly/are hard to find.

I'd personally go for the 400s brand new. Good unit.

Each to their own though! f**k digital >_<

im pretty sure craig (PREISS) had/has his DJM400 up for sale too Vinnie

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...