Jump to content
SAU Community

Front/dump Pipe Same As R33?

kidafa
 Share

Recommended Posts

kidafa Veteran

kidafa

Posted
Posted

Just wondering if the front/dump pipe of a r33 gtst is the same as the ones for a s1 stag... dont see why it wouldnbt be as their both running rb25det's.

Justjap also have the same pipe listed for r33/r32 and wgnc34's....

Thinking about buying a 3" bellmouth zx force dump pipe tomorrow for the stag. Then time for a retune of SAFCII, SITC and EBC and i think im done on engine mods till its time for a bigger whistling friend. Maybe time for some slotted rotors.

Link to comment
https://www.sau.com.au/forums/topic/268139-frontdump-pipe-same-as-r33/
Share on other sites
QWK32 Veteran

QWK32

Posted
Posted

I think if you buy one of the cheap brand dump pipes the R33 & R32 are the same pipe, the one I got for my 32 didn't sit quite right, so I suspect it was an R33 one. I used the one off my 32 on my S2 stagea and I had to cut it and realign the angle at the bottom straight section. Also had to add about 25mm length to the pipe to get it to meet up properly, this is for the S2 though.

DSTROY Grand Master

DSTROY

Posted
Posted
Well chad how about I be the test dummy and ill post up how it goes :P

Also when are we taking both our racing heart equiped stags out with jetskis in tow?

When you tell me where i can get a decent tow bar from.

jippa Proficient

jippa

Posted
Posted
JJR dump pipe i got of justjap was listed for s2 .

think JJR forgot about the crossmember. had cut and straighten out the front/dump to fit it.

not alot of work. but for one that is listed to fit, it should fit

had the same thing with my s2 and the just jap bellmouth.. the quality at the turbo end flange was very average to.

i would not recomend the jjr bellmouth as you will need to spend the extra money going to the exhaust shop for them to fix it

kidafa Veteran

kidafa

Posted
  • Author
Posted

Ok so it did fit.

When i first started the car their was a VERY ANOYING WEIIR vibration coming through the floor of the car around the G box area. Last for about 20 secs.. then dissapeared? Thinking it might have been hitting the floor of the stag, then settled itself down?

Drove around for a bit to let the beast warm up then gave it some. Car hit highest boost it ever has (13.something psi) so I turned down the ebc till it was hitting 12. So it must have made a difference :D

kidafa Veteran

kidafa

Posted
  • Author
Posted
When you tell me where i can get a decent tow bar from.

Well the place I got mine from was well priced but they Fu(ked my rear bar (ended up getting it resprayed for me) and the interior needed some adjusting by myself before it all layed flat in the boot. Want to meet up so you can check it out?

kidafa Veteran

kidafa

Posted
  • Author
Posted

So this vibrating was their thismornign again....

Took of the G box support cos it was might close to that and buzzed 2 mm off it on the very outer edge near the dump(its not sturctual dw!) Start up and its gone... Then it rattle a tiny bit again grrrr!

Realised its prob a mm or 2 from the floor of the stag and sometimes will vibrate on it but only for first couple of seconds or randomly for a couple of seconds when going slow.. Ill see how it goes and if it does it at all while cruising or at traffic lights.

DSTROY Grand Master

DSTROY

Posted
Posted
Well the place I got mine from was well priced but they Fu(ked my rear bar (ended up getting it resprayed for me) and the interior needed some adjusting by myself before it all layed flat in the boot. Want to meet up so you can check it out?

Sure man, sounds good. I should be picking up the Stag on Wednesday, I'll prob be cruising around all weekend in it :P

So this vibrating was their thismornign again....

Took of the G box support cos it was might close to that and buzzed 2 mm off it on the very outer edge near the dump(its not sturctual dw!) Start up and its gone... Then it rattle a tiny bit again grrrr!

Realised its prob a mm or 2 from the floor of the stag and sometimes will vibrate on it but only for first couple of seconds or randomly for a couple of seconds when going slow.. Ill see how it goes and if it does it at all while cruising or at traffic lights.

If it keeps doing it just take it down to an exhaust shop and they should be able to heat the pipe and bend it slightly, if its stainless it might be to hard to bend.

kidafa Veteran

kidafa

Posted
  • Author
Posted

yeah it only just taps it a tiny bit when it first starts then its gone....? Might loosen off the cat bolts a tiny tiny bit and see if that drops it down abit...

If that doesnt work ill take it off spray the seciton of pipe and under car where i think its rubbing drive around for a week or soo. rip it off and c where the paints gone to work out what i need to either smack flat or remove or if i need to get it bent slightly.

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted
yeah it only just taps it a tiny bit when it first starts then its gone....? Might loosen off the cat bolts a tiny tiny bit and see if that drops it down abit...

If that doesnt work ill take it off spray the seciton of pipe and under car where i think its rubbing drive around for a week or soo. rip it off and c where the paints gone to work out what i need to either smack flat or remove or if i need to get it bent slightly.

Yep that'll work if you haven't got a gas set and its just touching in one small area.
webng Experienced

webng

Posted
Posted

Hey Chris, good to hear you got it on.

When i fitted mine myself, if you remember i wasn't too sure if it was on/sealed 100%. So when i got my 100k service, i got the guys at Boostworx to have a look at it. They told me a couple of bolts had dropped off (probably because i didn't/couldn't get them tight enough to start with) and they redid the entire thing properly. Maybe it's a bolt rattling around somewhere?

kidafa Veteran

kidafa

Posted
  • Author
Posted

Hi nick! Long time no see :P Yeah their a prick to get at those bolts but it wont be one loose.... Got to them all in the end did change one of them to a 6mm allen key so it had a smaller head cos the bolt was fouling on the dump.

Dont really want boostworx doing much to the stag apart from tuning safcII and SITC truth be known, but we'll keep why off the forums :( cos their good blokes.

kidafa Veteran

kidafa

Posted
  • Author
Posted

Well I went to D N T performance (exhaust shop here in adelaide) on sat to get a 3" off cut to do the intake pipe mod, while i was their I told them about the dump pip tapping the floor. They said to unbolt the cat back and just pull the dump pipe downwards to bend it a tiny bit. Yesterday arvo gave it a good yank and its all sweeettttt :blink:

QWK32 Veteran

QWK32

Posted
Posted

your alot more game than i would be, pulling down on the pipe, i'd be worried about damaging the turbo casting. lol

just take it to the exhaust shop you went to and see if they'll fix it up for you, if you go in they aren't too busy, and you have cash with you, they'll probably fix it up cheap for you. it will only need to be cut and re-angled, maybe a small length added into it. shouldn't need to take the pipe out to fix up, we didn't when i fitted mine.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
    • Marek
      Hi everyone.

      By Marek · Posted

      Hi, Marek here 🙋‍♂️. I finally fulfilled my longtime dream - recently bought Stagea and now waiting for it to arrive in Poland. There's only few of these in my country, and one of the owners  recommended mi this forum as a source of all the info i'd need since now i own one  so here i am.  
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
    • Dose Pipe Sutututu
      Ethanol Content Sensor - Always at 11%?

      By Dose Pipe Sutututu · Posted

      and it ends up being already priced in as though you're just on 91RON without any ethanol. Car will lose a bit of economy as the short and long term fuel trims bring down the AFR back to stoich or whatever it is for cruise/idle for the engine.  
    • soviet_merlin
      Ethanol Content Sensor - Always at 11%?

      By soviet_merlin · Posted

      Oh, you are right. But, in Australia E10 is based on 91RON fuel and ends up being 94RON. Hence it being the cheaper option for economy cars. The more performance oriented cars go for the 98RON fuel that has no ethanol mixed in. The only step up we have left then at some petrol stations is E85.
×
×
  • Create New...