Jump to content
SAU Community

Recommended Posts

Im looking into getting new tyres as my rears as quite worn especially after doing a level 2 driving course.

My step dads making a fuss saying i have to get the same tyres as the ones i have on the front. The front tyers i have on are Nankangs ive had them on for over a year and still plenty of tread left on them

The rear is my second set..had nankangs which were crappy on the rear and wore them out now have worn Austyre or something cant quite remember.

Im asking if it will make any difference putting different type of tyres on as they have different tread pattern????

someone please shed some light on the situation

okay well i quickly looked it up in google and most people have said that its fine aslong as they are the same size. So the brand/tread wont make a difference, just got the make sure i get them aliigned.

yes its fine. The only time it would cause an issue is on the track where they will warm up differently. Even then its not a massive problem as front and rears warm up differently anyway!

it depends really but since its an rwd i would make sure u got good ones on the back. I got 235 potenzas on the front and hancook 265 on the back. NO issue at all, just make sure that they are pairs :D

My Dads the same "must have same tyres front and rear, blah blah blah" yeah maybe thats what they had to do in the olden days, when they had to have the same tyres front and rear whilst dodging dinosaurs on the way to the shops!

yes its fine. The only time it would cause an issue is on the track where they will warm up differently. Even then its not a massive problem as front and rears warm up differently anyway!

^^^+1

I had this issue when my Potenza RE-01Rs wore out at the rear. I replaced them with Toyo Proxes.

The difference in heat build-up was such that the Proxes felt mushy. When my Potenzas wore down at the front & replaced with Proxes (as a matching set), everything was sweet again.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...