Jump to content
SAU Community

Recommended Posts

Mine is a custom enclosure, technically, it sits where the spare tyre used to sit...

I've never had one above the fuel pump but that seems to cause alot of people problems. You'll probably find as well now that your RCA cables have been penetrated by the power and are creating noise, they will not shield as much anymore. Weird how it works like that but I've seen it happen a few times...

Can you ground your RCAs in any way? Normally the good ones have an extra cable running with them that you can ground to help minimise noise.

Here is a pic of my setup, completely useless to you, just thought I would share :DClicky!

Link to comment
https://www.sau.com.au/forums/topic/269049-rca-noise/#findComment-4582770
Share on other sites

i been trying diff grounds for amp no luck , bit better but noise does not go completely.

gets higher when i switch my lights on :D

i also tried relocating leads , only other way i can thing is if i run them thru middle of the car ...take passenger seat out and run rca's throught .

i cant ground my rca's , doof that setup is nice ;)

thanx for quick reply's boys

Link to comment
https://www.sau.com.au/forums/topic/269049-rca-noise/#findComment-4582785
Share on other sites

Crossovers will be fine. Do you have a spare set of RCAs? Even ones that aren't shielded?

Like I said, once the RCAs are corrupted, without getting new ones, you're going to have a tough time getting rid of the noise completely, but you have to sort it out or the same thing will just keep on happening.

What spec is the amp? And what grounds have you been trying? I would keep trying to find a good ground if I were you, maybe sand back some paint if it's stopping a good connection.

What about your battery? What's that like?

Link to comment
https://www.sau.com.au/forums/topic/269049-rca-noise/#findComment-4582822
Share on other sites

i got a new set of rca yesterday , amp is mtx maybe 6-7mnth old(about 60x4 rms)

i took the spare tyre out and there's few points where i sanded paint off and put ground there.

battery is standard.

did you run your rca and speaker cables together or yours are separate?

damn corrupt rca's hehe

i might try taking h/u out and checking if any of looms cables are cousing it but i doubt that.

Link to comment
https://www.sau.com.au/forums/topic/269049-rca-noise/#findComment-4582838
Share on other sites

I'm trying to remember how I did mine...

I ran a lot of wires up the middle but I forget which ones :D basically, I kept all RCA and any power wires very seperate (i think)... I've never had a problem.

My system is set up just a WEEEEE bit different to yours though... not a very good base for comparison at all.

Link to comment
https://www.sau.com.au/forums/topic/269049-rca-noise/#findComment-4582864
Share on other sites

i took the head unit out fiddled around a bit lowered noise tiny bit but once i turn my headlights on noise is back.

im getting sick of it , i think i will take the amp out and run the system off deck , i only run rears and fronts

the whine is killing me hehe

Link to comment
https://www.sau.com.au/forums/topic/269049-rca-noise/#findComment-4582927
Share on other sites

I've run RCA's next to speaker power wires, they are twisted pair RCA's though and I don't have an issue.

Not sure if it was the twisted pair construction which helped or not, I'd like to hear an opinion on that. The guys on Mobile Electronics seem to recommend twisted pair RCA's to prevent interference...

I also had what looked like car power wires running up the LHS and RHS of the car (battery in boot) I tried to keep away from them but the RCA's are pretty close, no issues though...

Link to comment
https://www.sau.com.au/forums/topic/269049-rca-noise/#findComment-4582957
Share on other sites

heres a few things to have a look at.

re-earth your car not just the amp.

That crappy earth wire that runs from the passenger inner guard to the exhaust manifold on a r33 needs to be replaced with something that is thicker and can handle more current difference.

Your head unit, a nice thick piece of graound cable from the chasis of the car to the chasis of the head unit.

Your power wire from the amp to the battery, move it away from the fuses and main feed for the car.

your earth wire on your amp - connect it to a different bolt in the boot than the factory earthing bolt under the battery.

make sure all the connectors you use are soldered, dont just rely on those crappy "gold" screw type connectors.

RCA's - twisted pair is a marketting ploy to get more $$ outta you. The amount of money you would need to spend on a system to hear an actual difference in RCA performance is more than you would spend buying a r33.

you can just always earth the outer sheilding on your existing rca's aswell..

if you do these basic's it should be fine as long you have good quality equipment.

My amp sits on a piece of timber mounted above a hi-flow intank fuel pump and the system has no noise to it.

Link to comment
https://www.sau.com.au/forums/topic/269049-rca-noise/#findComment-4582988
Share on other sites

to grond the rca's

you need to

- be careful

- cut through the plastic sheilding of the rca cable til you get the braided cable..(this goes to the outer part of the rca plug.. and it may also be a wire rather than braid on cheap rca...

- do not break this braid/wire - join another wire onto it

- becareful when soldering as to not burn through your rca's totally

- do near both ends of the rca cable

- once you have a wire soldered in at each in - earth each wire directly to the chasis

- do not earth them to other wires or amp/head unit earths.

thats about it, take your time and dont rush..

Link to comment
https://www.sau.com.au/forums/topic/269049-rca-noise/#findComment-4583095
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...