Jump to content
SAU Community

Rb25det Series 1 And 2 Turbo Differences?

Stunn-R

By Stunn-R,
in Engines & Forced Induction

 Share

Recommended Posts

DRD-00F Grand Master

DRD-00F

Posted
Posted

If you have a GT2871, they're all worse then that...

If I remember correctly, the series 2 turbo had a front wheel made out of some sort of polypropolene that made it lighter and spool faster, but I could be wrong...

Either way, they're both pretty shit... Brittle exhaust wheels and tiny housings...

Turbz RB-25 Experienced

Turbz RB-25

Posted
Posted
i did search and couldnt really find anything worthwhile, but i searched a while ago and i think i read the series II is a little biggER?

Nope, not bigger.

Made of different properties. S2 turbo can be boosted a little more as the material the compressor wheel is made of is lighter and a bit stonger.

Other than that, same shit, different smell.

paulr33 Grand Master

paulr33

Posted
Posted

assumption city

they are basically the same, the s2 cant handle more boost

anything around 12 or higher will kill the turbine, or put it at risk

running 12psi or higher, you are basically saying, i accept if the turbo fails and have $ to replace it

this is same for R33 series 1 or 2

the s2 has a different compressor wheel, but its far from stronger

DRD-00F Grand Master

DRD-00F

Posted
Posted
assumption city

they are basically the same, the s2 cant handle more boost

anything around 12 or higher will kill the turbine, or put it at risk

running 12psi or higher, you are basically saying, i accept if the turbo fails and have $ to replace it

this is same for R33 series 1 or 2

the s2 has a different compressor wheel, but its far from stronger

Soooo what's different about it?

Turbz RB-25 Experienced

Turbz RB-25

Posted
Posted
assumption city

they are basically the same, the s2 cant handle more boost

anything around 12 or higher will kill the turbine, or put it at risk

running 12psi or higher, you are basically saying, i accept if the turbo fails and have $ to replace it

this is same for R33 series 1 or 2

the s2 has a different compressor wheel, but its far from stronger

It's stonger. Search, and you shall find as well.

bubba Grand Master

bubba

Posted
Posted

No, it's not.

Personal experience.

RB25s2 is not stronger than s1. The nylon compressor wheel like to delaminate when leant on too hard.. had one in the workshop not so long ago with lots of bits of nylon missing of the wheel.

I recently sold my RB25s1 turbo, that thing spent a year getting abused at 12psi on my RB20 and another year getting abused at 12psi on my RB30 while also being a restriction, which meant the exhaust housing was getting super hot and the exhaust wheel still didn't fail.

RB25 Neo turbos have a slightly bigger exhaust housing.

I think it's pretty much luck of the draw, boost it over stock and it can fail sooner than if you didn't boost it.

That being said, I still prefer RB25s1 turbos and will advocate them over the later nylon wheeled units.

DRD-00F Grand Master

DRD-00F

Posted
Posted

I'd have to agree with the Series 1 turbos being stronger, but would also say the series 2 spool up faster. But when standard we're only talking like 100rpm or something anyway, it's pretty much instant!

bubba Grand Master

bubba

Posted
Posted

Umm.. Series 1 turbo has a STEEL compressor wheel while Series 2 has a NYLON compressor wheel. BOTH TURBOS HAVE CERAMIC EXHAUST WHEELS.

Oh and doof, of course the nylon wheeled turbo spools up marginally faster.. that was the whole point of the lighter compressor wheel :D

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Did you panel beat the dents or have you tried to repair this only using filler?  Is your sanding block soft/flexible and is following the shape of the panel rather then just knocking down the high points? 
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      I haven't knocked them down yet. I think I made the repair more complex than it should have been. I had rock chips combined with waviness and dents and I tackled it all in one because it was near each other and just end up wasting a bunch of bog lol. I'll knock down those areas and see how I go. And yep what you are saying at the end is correct. I think I might be sanding the top of a steep hill then my sanding block falls into the dent and gets rid of the guidecoat if that makes sense. Though shouldnt unless I'm covering too big of an area with not a long enough block. I'll try something new and provide some updates. Getting there though! Thanks as always.  
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Yeah makes sense, hard to comment on your situation without seeing what your doing. I was talking generally before, I would not be looking to randomly create low spots with a hammer to then have to fill them.  It's hard without seeing what your doing, it sounds like you are using the guide coat to identify low spots, as you're saying the panel is still wavy. I don't see how you're not ending up with patches of guide coat remaining in a wavy panel? Once the high spots are knocked down to the correct level, surely to have a wavy panel you need low spots. And those low spots would have guide coat still in them?
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      So I'll put filler past the repair area a bit to make sure I don't miss anything. Then I'll block it until it's almost level, put the guidecoat, then keep blocking until it's gone. Then it's still wavy.  In regards to hitting the panel, I saw this video might give more context - Skip to 0:47 he knocks it down. But yeah I'm sanding until the guidecoat is gone then checking because otherwise my filler is still well above the bodyline. Unless what you're saying is I should put guidecoat around it early, surrounding the filler then stip once it's gone?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      I refreshed the OEM injectors with the kit and connected it up. It now ideals okay even with the IACV removed. Driving still has the same cutoff issue like the 550cc injectors so the issue is somewhere else. I bought FPG's Fuel Pump Hanger. I will be installing it next, but it is not as straightforward as I thought it was with my limited wiring knowledge and no instruction on the specific model I purchased (FPG-089). I also got the incorrect billet clamp as I could not find info on the OEM sizing.
×
×
  • Create New...