Jump to content
SAU Community

Garage Defend Cooling Panel

GUN_METAL_GTR32
 Share

Recommended Posts

GUN_METAL_GTR32 Grand Master

GUN_METAL_GTR32

Posted
Posted

hay guys

just a quick question

i want to get a garage defend cooling panel from nengun but in the list of compatible models it does not list the r34 gtt.

does any body know if the r34 gtr one or the stagea wc34 one will fit with no hassles.

thanks

julz

Link to comment
https://www.sau.com.au/forums/topic/269845-garage-defend-cooling-panel/
Share on other sites
FineLine Grand Master

FineLine

Posted
Posted
i also wanna know if the r33 gtr one fits r33 gtst cos its not listed

what are the prices of these in AUS$ ??

Dont quote me but I think you may have some minor issues doing this.

I just did a full gtr conversion to my series 1 gtst and when i tried the gtst air guide I ran in to a prob.

The bonnet latch and mechanism sits about 20 mil higher on the gtr and when I tried the gtst airguide it fouled on the mechanism.

As to what would happen after I trimmed the airguide to fit I really dont know but I will do it at some stage in the near future.

Hope this helps.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
    • PranK
      Chris' Toyota Mark ii JZX110

      By PranK · Posted

      This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
    • soviet_merlin
      Duncan's V37.......race car?

      By soviet_merlin · Posted

      Thanks for doing that Duncan! Makes you a good person in my books. We don't get kangaroos or wombats here. But we have bats and it's similar. AFAIK it's often the mums with a baby attached that get hit because they drop lower when starting from a tree. If you hit an animal, check on it. https://www.ifaw.org/au/resources/wildlife-rescue-app An app to get the closest wildlife rescue contact.
×
×
  • Create New...