Jump to content
SAU Community

Recommended Posts

Trust TD06 L2 20G Turbo kit to suit RB20/25.

Comes with 44mm Trust Type R External Gate & Screamer pipe

Trust Highmount manifold, Apexi Power Intake to suit and Z32 AFM.

Oil line and all neccesary clamps,screws etc etc.

Genuine ARC Turnflow FMIC

Speco Fuel pressure regulator

Zero play in the turbo

edit- also comes with trust dump pipe.

Only selling as a complete package - $5500neg

Will sell as turbo kit alone with out AFM, Intercooler, Power Intake for $3600 neg

ARC turnflow Intercooler-

Reasonable condition, typical marks of use on it, no leaks, comes with piping of course.

$800neg

RB25DET NEO long motor + Gearbox

Circa 120xxx kms on engine, healthy engine, can be seen running. Gearbox happy and healthy also, No Clutch. Both regularly serviced by R.E Customs and Dr Drift. Loom and NISTUNE fully programmable ECU. Currently under the care of Dr Drift, but can also be tuned by Trent @ Status in Melbourne. There are tuners Aus wide aswell.

$4000 neg

Recaro Sr3 Millenium seats

Black, reasonable condition, inspection a must, slight tear from belt on drivers seat.

Pics up soon.

$1200 w/o rails $1600 w/rails

Work s2r rims.

R 18x10.5 wrapped in near new Kuhmo Ecsta rubber 265/35/18

F 18x9 in near new Nank Kangs

These fill the big big guards on the 34 very, very well.

Centre painted black, plenty of dish. Rear gaurds needed rolling to clear the rubber. a 255 with a tiny bit of stretch will clear.

post-30264-1242374589_thumb.jpg

Better pics to come.

$2200 neg. Rear tyres are worth $350 a piece and are at an even 95% wear.

Melbourne Pick up is preferred/welcomed.

Interstate buyers, contact me and we'll see what we can arrange.

More pics coming over the next few days.

No rush to move any of this, plenty of time while the next engine and box are going in.

Contact VIA P.M or email @ [email protected]

hay buddy

how r ya?

do u remember ages ago u pulled into the 7/11 on bell street and there was a white r34 with a flat tyre getting air? tht was me lol

any way just a question what type of spolier do u have on ur car ive never seen one before and love it.

cheers, and free bump quality parts right here

julz

Hey Julz,

glad you got home okay, lol.

It's a Mines Carbon ducktail.

Only other I have seen in Oz didn't have the carbon blade in it.

The only other ones I have seen in pictures are on an Autech 4 door 34 GTR and the Blitz R34 GT-R promo shots from the first release.

Good luck in your search :)

  • 1 month later...
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...