Jump to content
SAU Community

Wold 3d For Skyline

tdkmatt

By tdkmatt,
in Western Australia

 Share

Recommended Posts

tdkmatt Enthusiast

tdkmatt

Posted
Posted

hey, ive got greey emanage ultimate and havent installed it and tuned it as yet and ive got wold 3d v4 and i think id rather go with a full standalone than a piggy back, anyway i cant get a list of parts i need to install it straignt into my car, ive got wolf, hand controller, loom, but what sensors and such do i need?

Link to comment
https://www.sau.com.au/forums/topic/271407-wold-3d-for-skyline/
Share on other sites
reNEGaDe88 Proficient

reNEGaDe88

Posted
Posted (edited)

Wolf would be a way better ecu seeing as it a full ecu. There will be many more parameters that can be adjusted more if its a stand alone one. The guys at Top Racing tune the ecu's. I have a wolf 3d and my car runs well with the tune.

I think u need an adapter loom box and I think a MAP and water temp sensor. You don't need to run a AFM if u don't want to unlike the Apexi Power FC's. Give the guys at Top Racing a call for info.

Edited by reNEGaDe88
datsit Contributor

datsit

Posted
Posted

with you wolf you will only need the bigger turbo. standard injectors are good for just over 400rwhp. my car has a rb25 with a wolf and 040 and its making 390rwhp, my friend has a r33 gts that was 420rwhp with a wolf and standard injectors. Only thing is with wire in it only has 4 ignition out put so you have to batch fire the coils, the plug in has 6 out out unless you have the wolf v4 plus.

mitchy_ Grand Master

mitchy_

Posted
Posted
with you wolf you will only need the bigger turbo. standard injectors are good for just over 400rwhp. my car has a rb25 with a wolf and 040 and its making 390rwhp, my friend has a r33 gts that was 420rwhp with a wolf and standard injectors. Only thing is with wire in it only has 4 ignition out put so you have to batch fire the coils, the plug in has 6 out out unless you have the wolf v4 plus.

stock injectors will NOT make 400rwhp, they are 370cc and good for about 300rwhp.

either both of you aren't making anywhere near your 'supposed' power, or you're both running lean as f**k.

Dsturbd Grand Master

Dsturbd

Posted
Posted
standard injectors are good for just over 400rwhp. my car has a rb25 with a wolf and 040 and its making 390rwhp, my friend has a r33 gts that was 420rwhp with a wolf and standard injectors. Only thing is with wire in it only has 4 ignition out put so you have to batch fire the coils, the plug in has 6 out out unless you have the wolf v4 plus.

I recall a 33gts-t with wolf ecu making 511hp on stock injectors a few years back :blink:

tdkmatt Enthusiast

tdkmatt

Posted
  • Author
Posted

umm, well i dont have the plug and play version, ive got the wire in, so pretty much my tuner will know what to do? and does anyonme have the turbo and or injectors for sale?!?!?!?! id like to put some phwen down

Brockas Proficient

Brockas

Posted
Posted

Who's you're tuner?

There's only 1 person in WA with the patience to tune Wolf, everyone else will tell you to ditch the ECU and buy a Power-FC.

PICK YOUR TUNER FIRST, then buy the ECU he recommends. Not the other way around.

R32 Driver Mentor

R32 Driver

Posted
Posted

Yep pick a tuner before you buy an ecu, no matter how cheap the ecu may be

also something more popular like power fc, haltech etc would be better incase you dont like the tune

you can tell the tuner to f**k off

cars use/hp goal = choice of turbo + injector

reNEGaDe88 Proficient

reNEGaDe88

Posted
Posted

Emanage is a good piggy back ecu. Status tuning work with them. Slap it in the for sale section if you want to sell it.

Agreed with Mitchy, stock injectors are good for 300rwhp, not much more safely.

You can get a stock turbo hi flo'd for 2K and then u could make around 350hp I think.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • wizlb
      Who has a Infiniti Q60, Q50 (V37)?

      By wizlb · Posted

      I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Kinkstaah
      Starting again

      By Kinkstaah · Posted

      Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...