Jump to content
SAU Community

Need Some Help With My Turbo Timer

JamesK

By JamesK,
in Victoria

 Share

Recommended Posts

JamesK Experienced

JamesK

Posted
Posted

Posted this in the Security and Alarm section but didn't even get a single reply you guys here always seem pretty helpful so hopefully one of you guys can point me in the right direction?

Well basically my R33 GTST 1995 came with a nifty simple as chips pivot turbo timer it's controlled by a rotary dial with a selection of 0 1 or 3 minutes the actual unit is just under the fuse box and it's seems pretty straight forward but I have no idea what wire is what. The problem is that my Turbo Timer appears to be linked to the ACC rather then just the ignition so when I turn the car off everything stays on and my alarm system wont activate until it turns off and even more of a problem is that the doors automatically unlock (which I can turn off but I'd love it it worked properly) when the engine shuts do you guys know if this is a hard fix? I'm assuming its a few wires needed to be switched around but I just cant figure out which!

Also if you guys know how to setup remote start that would be great to, it's all set up but i cant find out where to put the ignition sense wire! The cluster is all electronic so nothing there and cant find anything in the engine bay :)

Any help is appreciated in advance

James

Link to comment
https://www.sau.com.au/forums/topic/271431-need-some-help-with-my-turbo-timer/
Share on other sites
Al Grand Master

Al

Posted
Posted

My alarm had to be turbo timer compatible.

ie: When i purchased the alarm, i was asked if my car was turbo and if i had a turbo timer. They then supplied an alarm that would wait for the engine to stop, before immobilizing; the doors lock, etc while the engine is running.

If your alarm is not compatible you'll need to put up with it or buy a new alarm.

JamesK Experienced

JamesK

Posted
  • Author
Posted

Yea AL it is compatible but the way it works is that it arms when the ACC has been turned off I thought it wasn't compatible and was just dealing with it until I met someone on teh Pizza curse who had the exact same alarm and his was all fine and dandy which got me thinking on getting these things fixed

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sunsetR33
      Ball bearing turbos

      By sunsetR33 · Posted

      Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • GTSBoy
      R33 GTST Axles

      By GTSBoy · Posted

      There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • jdniss
      Forced Performance Hta Turbos

      By jdniss · Posted

      Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • thozza
      Intro/R33 owner

      By thozza · Posted

      Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Lithium
      Forced Performance Hta Turbos

      By Lithium · Posted

      Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
×
×
  • Create New...